Jump to content
SAU Community

Recommended Posts

Just wanted to share with everyone some concrete information regarding replacing boot struts on R33 skyline, specifically the GTR but I am sure the information will be transferable. The reason I am posting is that there wasn't much information regarding pressures & the ability to remove the strut from the bracket (requiring drilling).

What I did ended up costing me $110.

Below is a picture I pulled from another thread, this is the part of the strut that is hard to remove. Very hard, but not impossible. What we did was use my 10mm spanner and wedge it in between the ball and the strut, then slowly work the it off. It looks like it's going to snap the strut and it ends up destroying it, but that's ok because new ones are cheap.

boot-struts.jpg

This is what mine looked like in the end.

_l_YlkhMrhBQ8EuTW0y2zCoronteQxKCJER7sheMowcDwPIacsgt8UsL1x21IK-aTNXtvJXg3_kDwKUO7ncCs5DhF97OgP03zCT2utJVgpasCM6swm6c6yBZghppOjRhrCDRNymusekRCAFCSLVeDDiJm-IyBLP34tFaLLj8iCNpO2l6-UBwXrdBHA8BrnRC2PnUvzFoIlPfql9mXz8kCw2L9ytvHw6U1scTkSBwqeMqsIX3wNksn_sPAbpZy7Kvlh3mOQGX7KphM2zUYUYY7fQyb_6DonTPI7HHveh-rqFTAxWNHIakGcNYvps9VAVQj_mvLAeoAlYLLJc-G9y9JH0t6EtBHhm5yN24o8_VHlDPboaZSpn4JoPdTUqAsb1Bh6kMrn--BwO5A_lftYEt7veVc8Mlg_eRZDr1nmb-pRaFW7WM8t08Ovg1xyN9jqbzhrRYS7wM9y4AxFwLHATXOaDlynuPHkZcUgY0ibAGwO6JeF_uLZs7dOxy4wcKj_m3rfQvjU6XJDkOfYiD5s24OyPnXqpZlMiQAxzc1wHM3VbEVKYgpPWqY3Ai_QBEcx5qndaGyljSAFyMJYY8KCQYhf5Icq7Vf4hdq6ORlGA=w731-h974-noMO_Ysbf9qqSSN3mh_W5cj--ZVZTDnQEdrg71b3qAL6ClwNPe2BAzRm9ffXwQtLNShfvVSrGZb1awzrTs-3wsiEDqajZLPoN-XH-oo3yrhDvt5S_iPPMs7CTedRr8Y9WVnNO4f4jH3znvJrerLZKaR1GZUm0gc0JunMDdDGBD_5Lga0DDMfHnarSUZq363IDwK97xkihWKBzrJRQAwiFYQw5j1Z9Dnv164W7OSwGE4XGxZ2eHIXysSShGk4IjHd_zD9SavOpyaH66YFmaVk38ecHVh0F1n5WLR9v8cqwuRQWMUZFyBWKd4hFCiprRS1wRgHjT9Iq1NS14jwjcKH2J9ydIEwV-D0wFsaZ5iPU1TVRZbW64atB04SPiQLer1iaCjN8IQuaboBUJBroqU-fMS23BF47Nh-odqGUvevbRwZJlZq-y8SrFnzt4yEWXv_Gd9q3ynKsZF2BcZsbcgSnhLdmijitWj445px4bXxpp9G_r_3lYpT3DMNRp0q12ksFoBKJ-o1_dLONJpkt8z3TBNpHHgJpGpvqu1omhtPLvdPN8GYOocaBcbO6StAmCCNv8PSKanLGhsXMwgLBHVr5axmsFFRB284OaLppLBXg=w731-h974-no

We ended up putting 100nm of pressure in each cyl. It holds the boot fine with a genuine GTR spoiler. If I had to do it again, I would put 150nm in each to see if it holds any better, BUT that 100 works just fine.

Any questions please shoot them through.

Edited by sleptema
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/474449-r33-gtr-gas-boot-struts/
Share on other sites

What's 100nm in real pressure units?  You have given units of torque.  Pressure is measured in Pascals or multiples thereof (like kPa, MPa, etc) or in psi for knuckle dragging 'Muricans.  Or in N/mm2 (equivalent to MPa) or in bullshit units involving the heights of columns of fluid such as water or mercury.

Yeah sorry guys, I was thinking about that this morning and realised how stupid I must sound aha. The guy who did my struts didn't correct me, I believe it would be newtons.

EDIT: Re-uploading pictures of finished product.

IMG_20180707_111049.jpg

IMG_20180707_111053.jpg

Edited by sleptema
  • 4 weeks later...
  • 4 weeks later...

Hi all,

I am also keen to know where I can buy these as I have been looking and found nothing except a few used struts on eBay.

Any help would be appreciated...Every time I need to use my boot at the moment I feel like I have my head in a guillotine!!

On 7/31/2018 at 12:02 PM, Ty1 said:

Where abouts did you get this done? And these are new struts yeah? or did you end up managing to reuse the factory ones?

I used a generic strut specialist. Old ones needed to be thrown out as there was no way they could be re-used. He just used the brackets from the OEM ones and adapted them to fit on the new struts.

I believe he just measured the extents of the struts and ordered accordingly, and put above mentioned pressure into them.

  • Like 1
  • 8 months later...

Hello

my Gas Strut were weak so I want to replace them.

This Topic pointed me in the right direction, thanks !

You can chosse this Model from Mercedes Part No.: 2218800329 

It s from the W221 S Class Hood strut.

You can find them for around 14$ on Aliexpress. They are a little bit too strong so I recommend to buy some used ones.

I only replaced one and the Hod stays in any angle.

I recommend to tap an M6 in the Bracket and add a nut to secure the strut.

They are a 14mm  to short, so the Trunk opens 12 cm less. Adding a spacer will fix this

I also replaced the rubber bumper . They are from Aliexpress also.IMG_2323.thumb.JPG.afe41b4eae5716055d1b1a494c668e28.JPGIMG_2326.thumb.JPG.1e7e979e952d3c797bb5eeadcbb3328a.JPGIMG_2328.thumb.JPG.0afff9f21876085c3da8d913c770010d.JPG

IMG_2327.JPG

IMG_2325.JPG

Edited by Fastlane
  • Like 1
  • 3 weeks later...

So I did some research, cause the Mercedes Strut were to strong

The original USED Struts have 30 kg while pushing and approx.20-25kg while holding.

The new ones should be around 35kg-40kg

And i Find the perfect one again on Aliexpress

search for:IMG_2392.thumb.JPG.21d8a83675800d67e8a9bd41aebdf543.JPG 320Mm 400N Flap Spring Flap Fitting Gas Spring !

they match perfectly.

The Trunk lid will hold until 15cm before reaching the lock.

 

  • 2 months later...
  • 3 weeks later...
On 13/08/2019 at 1:21 PM, rych said:

I hate to necro this but when you use a 10mm spaner to wedge the strut out did you had to drill a hole to make new strut fit? 

Nah, the strut guy just got a fitting on the new strut that fit over the 10mm ball joint.

  • 1 year later...
On 20/05/2019 at 8:47 PM, Fastlane said:And i Find the perfect one again on Aliexpress

search for:IMG_2392.thumb.JPG.21d8a83675800d67e8a9bd41aebdf543.JPG 320Mm 400N Flap Spring Flap Fitting Gas Spring !

they match perfectly.

The Trunk lid will hold until 15cm before reaching the lock.

 

Hopefully this is still correct years later because I’ve just purchased some. Cheers mate

  • 3 months later...
14 hours ago, joshuaho96 said:

I need a replacement for the trunk gas strut

https://www.ebay.com.au/itm/AUTOPA-Gas-Bonnet-Strut-for-Mercedes-W221-C216-S350-S450-S500-S63-A2218800329/254807343124?hash=item3b53b38014:g:5fMAAOSwBYteZbCj&frcectupt=true

here's the link on ebay for the struts, in stock in Sydney.

If you need any strange brackets or ends. Here's the link to a strange brackets or ends seller also local.

https://www.gasstrutaustralia.com.au/

4 minutes ago, Rusty Nuts said:

https://www.ebay.com.au/itm/AUTOPA-Gas-Bonnet-Strut-for-Mercedes-W221-C216-S350-S450-S500-S63-A2218800329/254807343124?hash=item3b53b38014:g:5fMAAOSwBYteZbCj&frcectupt=true

here's the link on ebay for the struts, in stock in Sydney.

If you need any strange brackets or ends. Here's the link to a strange brackets or ends seller also local.

https://www.gasstrutaustralia.com.au/

I'm in the US, my concern is that the gas strut is too strong. The Alibaba generic one is said to be more appropriate, so I'm thinking of trying one of those first.

  • 2 weeks later...
On 23/01/2021 at 3:09 PM, IM-32-FK said:

Don’t get replacement ones, you can get the OEM ones regassed. There’s a couple of places in Sydney that I know who do it.

Only if the seals are good. If they're not, which they probably aren't, they're a throw away. Just retain the top boot lid mounts to adapt to new ones.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...