Jump to content
SAU Community

Oil feed line routing

Murray_Calavera
 Share

Recommended Posts

Murray_Calavera Mentor

Murray_Calavera

Posted
Posted

Hi all,

I was wondering what the ideal way to route the turbo oil feed line is? 

The line that Tao supplied is so long it makes me think there is a particular reason for the length. 

I can only really think of 2 options, but both end up with a lot of excess line. I've attached a picture to show my thoughts. The squiggly lines aren't to scale but you get the idea lol

Oil feed routing.jpg

Link to comment
https://www.sau.com.au/forums/topic/480702-oil-feed-line-routing/
Share on other sites
Murray_Calavera Mentor

Murray_Calavera

Posted
  • Author
Posted

Ok, so taking on board everything said above - I've ended up with this. 

I'm thinking where the factory water bracket was, I can get a bracket made up to support the flexible oil and water lines that will run through there. 

20200702_214551.jpg

20200702_214728.jpg

20200702_214742.jpg

Murray_Calavera Mentor

Murray_Calavera

Posted
  • Author
Posted (edited)
10 hours ago, dyl33 said:

I would of ran it like the red diagram, not next to the dump pipe.

And maybe use some heat proof sleeve over it too.

I think your right. 3rd times the charm!

Originally I was worried about it getting too close to the oil drain line, but the bit it's near is metal. 

Edited by Murray_Calavera
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Also, would you not flip the hose around so the 90 degree is off the turbo and it's a nice gentle arch all the way to the fitting on the block?

Here's what I did before with my ex Hypergear ATR45SAT (great turbo, just got carried away with the TS route then replaced it before I tuned it).

20171119_150015_HDR.thumb.jpg.0506f2e3ff835819acf655c1d903a7ad.jpgT03.jpg.ed1381f835801c63ecc97bced93b478d.jpgIMG_20181201_092528.thumb.jpg.c26cf4943da6b4d8b27fdbf002da45ea.jpg

Ben C34 Grand Master

Ben C34

Posted
Posted
2 hours ago, Murray_Calavera said:

I think your right. 3rd times the charm!

Originally I was worried about it getting too close to the oil drain line, but the bit it's near is metal. 

It can touch the oil drain line, exhaust not so much!

Murray_Calavera Mentor

Murray_Calavera

Posted
  • Author
Posted
1 hour ago, Dose Pipe Sutututu said:

Also, would you not flip the hose around so the 90 degree is off the turbo and it's a nice gentle arch all the way to the fitting on the block?

Here's what I did before with my ex Hypergear ATR45SAT (great turbo, just got carried away with the TS route then replaced it before I tuned it).

 

Yep, I've flipped it around and put the heat shielding stuff on it too. I'll get a photo up a bit later.

hardsteppa Grand Master

hardsteppa

Posted
Posted

just putting it oot there...you can also just buy an AN4 stainless end and cut to a suitable length, get rid of the excess. Tao just prob does it that way to avoid emails of ' the line supplied is too short!" so makes it plenty long.

  • Like 2
Murray_Calavera Mentor

Murray_Calavera

Posted
  • Author
Posted
2 hours ago, hardsteppa said:

just putting it oot there...you can also just buy an AN4 stainless end and cut to a suitable length, get rid of the excess. Tao just prob does it that way to avoid emails of ' the line supplied is too short!" so makes it plenty long.

I wish I could have come up with this myself... especially as I made up that water line =/

Could have got the proper size heat shielding too rather then putting -6 shielding on it to clear  the fittings...

  • 6 months later...
Tobz Community Regular

Tobz

Posted
Posted (edited)

 

On 03/07/2020 at 10:02 PM, Murray_Calavera said:

especially as I made up that water line =/

Your new water return line, did you connect it to behind the head or did you cut the hard pipe and attach it there?

EDIT:  Hang on, how does the water line to your turbo work? 

Edited by Tobz
Murray_Calavera Mentor

Murray_Calavera

Posted
  • Author
Posted
15 hours ago, Tobz said:

 

Your new water return line, did you connect it to behind the head or did you cut the hard pipe and attach it there?

EDIT:  Hang on, how does the water line to your turbo work? 

Hey mate, I'm pretty sure I used the factory water line for the one your describing. 

The water line I made up goes from the turbo to the block and you can see it in the above photos.

Let me know if there was something in particular you need more details on.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Starting again

      By GTSBoy · Posted

      This is the GTR fuel pump. Yellow shows 12V, orange shows earth. The ECU provides the earth to activate the fuel pump relay. The ECU side of teh relay will pull low when the ECU activates. This is the RB20 fuel pump. Almost the same, but a little simpler. You can see I indicated (above) where the 12V line goes down to the RB20 diagram on the overall diagram, whch shows both RB26 and RB20. This is where I show it coming in on the RB20 diagram below. You can see that the dropping resistor is handled differently. When the fuel pump control is not providing earth to the pump, the pump earths through the dropping resistor and thus runs at lower voltage (some is wasted over the resistor) and runs slower. I showed that "not 12V and not quite earth" portion of the wiring in a paler orange. The rest of the wiring that I did not colour on that little section below the pump would be orange when the fuel pump coontroller is providing earth. This drop is handled inside the fuel pump controller in the GTR. Regardless, you can see where 12V is supposed to be, where earth is supposed to be. The key on prime is via the ECU providing the pump for only a few seconds the switching off. You should be able to see that happen.
    • Duncan
      Starting again

      By Duncan · Posted

      Yeah so when you turn key to IGN the fuel pump should run for a few seconds. If you find the fuel pump relay (and have a multimeter, and a second person) to can check the relay inputs.  One trigger pin should be either fully earthed  The other trigger pin should get 12v from the ECU for say 3 seconds when you turn key to IGN, and at all times that key is at START (note, I said this from memory, it may be the other way around, ie one pin always has IGN 12v and the earth has continuity to earth when you turn the key) One Pin should have a good battery voltage The last pin goes to the fuel pump + Also note that if the power to the relay is good, and the relay is working, it is worth checking the pump has a good earth too. There is a computer in the standard system that increases the earth resistance to slow down the pump when not required, pretty old school and it may have failed
    • Ozdavroz
      Starting again

      By Ozdavroz · Posted

      All this talk about fuel and fancy ECUs, meanwhile my poor old R32 has neither.... When the ignition is turned on, should there be power running o the fuel pump constantly or just for the few seconds it usually takes to prime the pump? About to go have another look at it, have watched some YouTube vids on how to use a  multimeter and looked at some wiring diagrams but really have NFI what I'm looking for because electricity is invisible  
    • GTSBoy
      R32 Nostalgia

      By GTSBoy · Posted

      Yuh....but weren't all the supertourers, except maybe the Audis, FWD? I don't recall any of the others being AWD.
    • Duncan
      R32 Nostalgia

      By Duncan · Posted

      They ran them in Oz Super Tourers too https://www.supertouringregister.com/register/vehicle/212/ (I'm so old I remember racing with Matthew Fox) They ran them in Oz Super Tourers too https://www.supertouringregister.com/register/vehicle/212/ (I'm so old I remember racing with Matthew Fox)
×
×
  • Create New...