Jump to content
SAU Community

Recommended Posts

Hi all,

Just wanting some advice regarding grout filling blocks.

Long story short, i am looking at building a new short block for my car as the current one has a 1mm crack that has been JB Welded and with the power it will eventually fail.

I have managed to find a virgin block r32 rb26 block, plan is to go billet main caps and plate. After talking to a few people online some people running big power on the cast blocks have also done grout fill along with bracing of some sort. I have talked to my engine builder about the idea of going half grout fill as it is still a street car and the setup for billet block is out of the question.

My engine builder has used Hardblok on old V8's, however they were for dedicated drag cars on methanol so heat is not really an issue. The issue is he has concerns about the grout separating from the bores from heat expansion with the different materials.

 

Cheers 

Jeff

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/
Share on other sites

  • 4 weeks later...

I think that the conservative approach is to grout up to the bottom of the lowest welch plug(s). Adds some stiffness but still allows the coolant pretty much full access to the bores. It doesn't put any grout around the part of the bore that might expand from internal pressure, but it certainly locates a clamp around the bore which constrains how far down the bore any such movement can occur, thereby reducing the amount of movement that can occur in the top half.

Perfect? No. Better than nothing? Of course.

There have been many people on here who have done pretty much what I described above. Read these.

https://www.sau.com.au/forums/topic/429446-strengthening-a-rb26-block/

https://www.sau.com.au/forums/topic/431462-grout-fill/

https://www.sau.com.au/forums/topic/210084-rb26-resin-filled-blocks/

 

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7952919
Share on other sites

My experience counts for zero as my engine has done no more than idle in the shed but I've done the grout fill to the base of the welsh plugs.  The lower part of the engine is the most common (only??) place that the blocks crack so makes sense to me to do it.  The hottest part of the block (top 4 inches where combustion happens) is not affected by grout so I see zero issues there.  I really see no downsides to it so if it only made 10% improvement surely it's worth it for the minimal expense of doing it.  I look at this way.  If I cracked a block and HADN'T done the grout, I'd never forgive myself for not giving it a fighting chance!

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7952920
Share on other sites

On 6/15/2021 at 4:01 AM, GTSBoy said:

I think I've seen RB26 (in particular) failures up high on the exhaust side near #4.

I'm sure the half-filled grout would help additionally strengthen to some degree. Especially with a PRP brace. Are blocks still cracking on that area with either or?

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7952995
Share on other sites

20 hours ago, r32-25t said:

26 blocks are common for cracking the deck, talking to Herman from prp said even full prepped all high power 26 blocks will crack eventually 

What kind of cars are breaking 26 blocks? I was watching Herman's youtube videos from 2 years ago and he said a number of high power GTRs are running the brace and not cracking blocks. He did mention grout filling too. I'm sure times have changed..

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953031
Share on other sites

Grout fill won't hurt. It's cheap anyway so do it.

If block cracks anyway what's the point of spending 2k+ on a brace?

If youre pushing 400+kW in a 'street car' it aint gonna be as reliable as social media say it's gonna be anyway. *flame suit on*

Thats the sport. Make bulk power and shit breaks.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953044
Share on other sites

2 minutes ago, WantGTR said:

If block cracks anyway what's the point of spending 2k+ on a brace?

There's almost certainly shades of grey here. For one thing, every engine and block is different. There's a bell curve of outright strength. On top of that, there's all the thousands of variables of how that block has been treated across its years of use, the power level that it has been run at, the particular mods/method by which the power is being made (ie power from more revs or power from more cylinder pressure). + how it is used. Street vs circuit vs drag, etc etc etc.

Then the next shade of grey is, for any given block, wherever it falls on that bell curve, surely adding the block brace still has benefits. Making the bottom end even less likely to walk around, for one. But I'd still expect it to raise the limit of that block before it will break. Trouble is, you can't go pulling out anecdotal evidence of "this block ran for 2 years at XXX HP without a brace and was fine" and "this other block broke at less HP with a block brace added", because the bell curve created by adding up all the uncertainties is likely to be far wider than the difference in power of those engines.

Unless you are in a position to gather a large number of statistics your (anyone's) statistics must be taken with a huge grain of salt. Confidence levels are only built up by having many examples with almost no difference between them to describe the average behaviour of that type of example (along with the other statistical parameters of interest, particularly the SD). There's no point comparing two examples if the stats are so poor that the SD is several times wider than the difference between the examples.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953047
Share on other sites

1 hour ago, GTSBoy said:

There's almost certainly shades of grey here. For one thing, every engine and block is different. There's a bell curve of outright strength. On top of that, there's all the thousands of variables of how that block has been treated across its years of use, the power level that it has been run at, the particular mods/method by which the power is being made (ie power from more revs or power from more cylinder pressure). + how it is used. Street vs circuit vs drag, etc etc etc.

Then the next shade of grey is, for any given block, wherever it falls on that bell curve, surely adding the block brace still has benefits. Making the bottom end even less likely to walk around, for one. But I'd still expect it to raise the limit of that block before it will break. Trouble is, you can't go pulling out anecdotal evidence of "this block ran for 2 years at XXX HP without a brace and was fine" and "this other block broke at less HP with a block brace added", because the bell curve created by adding up all the uncertainties is likely to be far wider than the difference in power of those engines.

Unless you are in a position to gather a large number of statistics your (anyone's) statistics must be taken with a huge grain of salt. Confidence levels are only built up by having many examples with almost no difference between them to describe the average behaviour of that type of example (along with the other statistical parameters of interest, particularly the SD). There's no point comparing two examples if the stats are so poor that the SD is several times wider than the difference between the examples.

i agree with what you are saying, lots of variables to take into account. i was just trying to make a point :P

 

People tend to jump on the bandwagon and want to include all the latest fancy new parts whether they are necessary or not. With today's technology, making 1000 or more isnt as out of reach as it used to be. Fact is there are more and more engines out there making lots of power even without braces. Toward the top end of the power spectrum, i firmly believe none of these engines are reliable no matter how well they are built or what parts are thrown into them and they are no where near as 'streetable' as the internet makes them out to be.

Either way you go, grout/no grout, brace/no brace, billet/cast, it is going to cost money and expect failures - not if but when.

 

Happy Modding.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953053
Share on other sites

9 hours ago, WantGTR said:

i agree with what you are saying, lots of variables to take into account. i was just trying to make a point :P

 

People tend to jump on the bandwagon and want to include all the latest fancy new parts whether they are necessary or not. With today's technology, making 1000 or more isnt as out of reach as it used to be. Fact is there are more and more engines out there making lots of power even without braces. Toward the top end of the power spectrum, i firmly believe none of these engines are reliable no matter how well they are built or what parts are thrown into them and they are no where near as 'streetable' as the internet makes them out to be.

Either way you go, grout/no grout, brace/no brace, billet/cast, it is going to cost money and expect failures - not if but when.

 

Happy Modding.

I think a brace is pretty clear that it is actually a very worthy mod. Yes, we can argue that every mechanical part can break with enough heat and stress but your points are blinding the degree to which this is highly probable vs. not.

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953066
Share on other sites

10 hours ago, cachorro said:

I think a brace is pretty clear that it is actually a very worthy mod. Yes, we can argue that every mechanical part can break with enough heat and stress but your points are blinding the degree to which this is highly probable vs. not.

The grout is a no brainer, the brace is a bit different as the cost and effort involved is a lot higher once you factor in machining, etc.  At the end of the day it's like an insurance policy.  You hate paying for it and hope you don't need it but bloody thankful you did have it when you needed it!

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953073
Share on other sites

I remember not that long ago this topic coming up on a GTR page on FB. Herman stated that a block brace is essential for any serious build. Then Anthony Maatouk chimed in and stated he has never used a block brace on a 26 block, however all his builds use an N1 block, claimed over 150 builds and not one block crack, tagged numerous customers to confirm, cars that have been running for years. 
Now he also stated he is not against the brace and uses them in all of his RB30 builds. Just his opinion is they are not required in an N1 block. Now this sparked a lot of back and fourth between Maatouk and Herman. Was all very interesting to hear both sides of the argument. Herman stating he has seen numerous N1 blocks crack and Maatouk stating it was likely other factors that caused that, (pointing towards bad tune). 
from a more personal point a mate of mine has a Maatouk’s built 2.7, running a 76/75 making 1000+ hp, been running for about 3 years now without issue. (Not braced). 

  • Like 3
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953074
Share on other sites

On 6/18/2021 at 8:04 PM, Old man 32 GTR said:

I remember not that long ago this topic coming up on a GTR page on FB. Herman stated that a block brace is essential for any serious build. Then Anthony Maatouk chimed in and stated he has never used a block brace on a 26 block, however all his builds use an N1 block, claimed over 150 builds and not one block crack, tagged numerous customers to confirm, cars that have been running for years. 
Now he also stated he is not against the brace and uses them in all of his RB30 builds. Just his opinion is they are not required in an N1 block. Now this sparked a lot of back and fourth between Maatouk and Herman. Was all very interesting to hear both sides of the argument. Herman stating he has seen numerous N1 blocks crack and Maatouk stating it was likely other factors that caused that, (pointing towards bad tune). 
from a more personal point a mate of mine has a Maatouk’s built 2.7, running a 76/75 making 1000+ hp, been running for about 3 years now without issue. (Not braced). 

Herman's videos are on youtube on the Motive Video channel and they are worth the watch. I wonder on what grounds Maatouk claims a brace is not necessary. It could be true but as mentioned, where on the bell curve does each individual block sit. Also there could be dozens of combinations of variables. Do you have a link to the facebook post? Curious to read up on it.

 

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953227
Share on other sites

8 hours ago, cachorro said:

Herman's videos are on youtube on the Motive Video channel and they are worth the watch. I wonder on what grounds Maatouk claims a brace is not necessary. It could be true but as mentioned, where on the bell curve does each individual block sit. Also there could be dozens of combinations of variables. Do you have a link to the facebook post? Curious to read up on it.

 

On the grounds that they have extensive experience and a solid track record of building the fastest RBs in the country. No other workshop comes close to having as many tough RBs as this place in the Australia or possibly the world. They certainly have credibility to make comments about the platform.

 

note: i am not a customer of theirs at all but just calling a spade a spade.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953233
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...