Jump to content
SAU Community

Recommended Posts

Above dyno sheet engine specs. I'm taking a cue from whats above so this is what I know.

N1 Block.

RPM 2.8 build. (don't know huge details)

Garret 2860-5 Turbos

RPM 4inch exhaust (twin 2.5 in tips)

HKS Vcam

HKS Cam Gears

E85 set up (Pumps etc)

Power FC

120mm intercooler

N1 oil pump

N1 water pumps.

Sard 700cc injectors

Nismo AFMs

I think thats all thats relevant. Has sump mods etc as well but figure not making a difference as far as power goes.

  • Like 2

Above dyno sheet engine specs. I'm taking a cue from whats above so this is what I know.

N1 Block.

RPM 2.8 build. (don't know huge details)

Garret 2860-5 Turbos

RPM 4inch exhaust (twin 2.5 in tips)

HKS Vcam

HKS Cam Gears

E85 set up (Pumps etc)

Power FC

120mm intercooler

N1 oil pump

N1 water pumps.

Sard 700cc injectors

Nismo AFMs

I think thats all thats relevant. Has sump mods etc as well but figure not making a difference as far as power goes.

Wow - cool setup. That must have cost a pretty penny to setup?

E85 on 700cc injectors?

Wow - cool setup. That must have cost a pretty penny to setup?

E85 on 700cc injectors?

I'll check on injectors as the car came with two sets and one of them was the ones we used but they may be 1000cc. Seems more likely.

It cost a bit. I'll say no more :)

Mick.

  • 2 months later...

Just got my car tuned 703rwhp 524rwkw. Does anyone know the record for these turbos?

Built bottom end with 87mm pistons

2860-5 turbos

Pon cam type A

Tomei manifolds and dumps

Apexi down pipe

ID1000s and tomei fuel rail

2 walbro 400lph fuel pumps

Nismo inlet pipes and hard intercooler pipes

Custom intake pipes

AEM series 2 ecu tuned for flex fuel

4CA2765D-A61C-43E6-9DCF-9E05E902C893_zps

Just got my car tuned 703rwhp 524rwkw. Does anyone know the record for these turbos?

Built bottom end with 87mm pistons

2860-5 turbos

Pon cam type A

Tomei manifolds and dumps

Apexi down pipe

ID1000s and tomei fuel rail

2 walbro 400lph fuel pumps

Nismo inlet pipes and hard intercooler pipes

Custom intake pipes

AEM series 2 ecu tuned for flex fuel

4CA2765D-A61C-43E6-9DCF-9E05E902C893_zps

I think you're the record holder if the above dyno read out is accurate.....wow

Just got my car tuned 703rwhp 524rwkw. Does anyone know the record for these turbos?

Built bottom end with 87mm pistons

2860-5 turbos

Pon cam type A

Tomei manifolds and dumps

Apexi down pipe

ID1000s and tomei fuel rail

2 walbro 400lph fuel pumps

Nismo inlet pipes and hard intercooler pipes

Custom intake pipes

AEM series 2 ecu tuned for flex fuel

4CA2765D-A61C-43E6-9DCF-9E05E902C893_zps

Really?

Judging by when that peak touqe hits they could be -10's.

Is this on std standard stroke, so a bit over 2.6?

What intercooler you running?

What exhaust?

What boost achieved that number?

Really?

Judging by when that peak touqe hits they could be -10's.

Is this on std standard stroke, so a bit over 2.6?

What intercooler you running?

What exhaust?

What boost achieved that number?

These are -5's I have a picture somewhere.

Block is built with 87mm pistons, eagle rods, and N1 crank

Stock Intercooler

When I bought the car the previous owner said the exhaust was blitz. The muffler says Kakimoto

We are running 25psi of boost.

Here a pic of the engine

00000000-0000-0000-0000-0000000000ED_zps

Here's a pic of the new inlet pipes

A7AF15C8-183C-4845-B030-E13041C0BC9E_zps

We are using E85. The 1000cc injectors are maxed out already so might have to change those out. Powerfab rents out the local drag strip in April to fine tune cars so I'll post trap speeds then. Also we are taking the car to another dyno this week.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Just trying to get my head around this. At 5psi of boost, you turn on your wmi pump, and then you're using a 3000cc injector, to allow flow upto the actual engine, where you have your 6x200cc injectors and a 500cc injector. If the above is correct, what advantage are you obtaining by having the 3000cc injector blocking flow, is this just incase a line breaks between that injector and the motor you can stop flow immediately? Or are the 6x200cc and 500cc less injectors and just spray nozzle?
    • Welcome! New member myself, but I had an R33 back in 2002. Best advice I could give, based on my experience: if you're running the factory turbo, be very conservative with boost. I made the mistake of just fiddling around with the boost controller and cranking the boost for fun, and the end result was my intake pipes popping off frequently from the constant deluge of oil that was being blown into the recirc by the stressed-out turbo, which itself was siphoning oil from the engine and farting it out both sides of its centre bearing (or something to that effect). If I could do it all again, I would have gotten a new turbo and had a tune dialled in professionally and then just left it alone! Funny you mention the metal shavings in the gearbox, as I had the same thing - the probe plug (magnetic drain plug, essentially) would come out caked with shavings. At least it was doing its job. Not sure if that's just sacrificial wear and part of the deal, or if my gearbox was shagged, but I wasn't abusing it. Enjoy the R33 - they're a dying breed, and if they weren't $35k+ on CarSales in Queensland, I might have picked up one of those again, instead of the 370GT I own now (though I'm loving the 370GT, that big 3.7L V6 just hits different).
    • Howdy folks. I owned an R33 back in 2002, which was thoroughly beyond my capacity (financially speaking) to maintain/insure, so we parted ways in 2004. Fast forward 21 years (to literally yesterday, in fact) and I'm now the proud owner of a 2007 V36 370GT. I'm happily surprised by how much power the VQ37VHR makes, compared to the RB25DET, considering the latter is turbocharged. I had planned to add a turbo at some point but I'm on the fence about whether I'll even need it (though I do love the sudden onset of extra torque). Any other 370GT owners around the traps, I'd love to hear about your experiences with this car (good and bad).
    • Perhaps the answer is... more jacks!* *proper jacks must be used.  
    • I NEVER think about using a scissor jack unless there is absolutely no other alternative. f**king things are dangerous, annoying and stupid.
×
×
  • Create New...