Jump to content
SAU Community

Recommended Posts

Not bad for 18psi any dyno graphs ?

When is it on full boost by

does it drive good and feel responsive on road or the car ain't registered?

On a cooler day should pick up another 10kw at least without even touching the tune

my mates built sr20 corolla was tuned last Thursday in 40degree heat made 330rwkw then went back on sat same dyno same tune made 357rwkw

Eh. I've seen cars do straight back to back runs in dyno competitions with more than 50 hp difference between them. Loads of variables.

The important thing is how the car drives, and by the sounds of it Scott is pretty happy with that, so I'd say it's a good result :) Also keen to see a graph though Scott! Any plans to switch to ethanol or WMI?

Thanks for the feedback guys, its just my luck to have it tuned on the hottest day recorded since 1930 lol

I got to have a little play once I got it back to the area and I can say it is fast. Its got a solid powerband from 4000-7000, a good 3k of fat power. I do think I might want to get it touched up on a cooler day though, there are a couple of areas that I feel could be improved.

Having let a friend drive the car first was a mistake lol, the stock 3.7 diff ratio can really make the car feel dead if your expecting it to boost from 1700. Once I jumped in for a hoot having a reasonable idea of keeping the thing on the boil made it a completely different animal all together.

Unigroup said the car gave them zero hassle, went on the dyno and tuned right up. They were very impressed with the way the setup behaved and said the motor itself was possibly the best built motor they have had come through there in a long while.

Ill attach the graph here for all to see.

post-43588-0-49785200-1358508792_thumb.jpg

Also got my car back from tuning by C-Red today. I was a little sad panda when Mark said It made 335rwhp on 16psi (they say they have a low reading dyno). However it pulls hard once again, like it did with 375rwhp on 21psi last year, so im wrapped.

It didnt seem to like 20psi very much with lots of pinging, so timing had to be taken out a fair bit.

Taking it to the drags on wednesday to see what's what. ;)

Going to try and improve on my results and sort out my issues once I get back into work. It's been ages and I'm still happy with how it drives but I feel something is holding my SS1PU back with it making 250rwkw @20psi

The WMI will help with the heat issue but before doing that I was going to check my whole exhaust and actually see what size it is throughout. Making sure the exhaust isn't the issue then I guess I'll have to move onto my intercooler.

Anyone heard of a 'Hybrid intercooler'? I must be lucky because it also says its limited edition haha

Most probably something cheap and this could be why I need 20psi to produce the same power as people running 16psi such as birds results.

Stao has given me some good advice to check the boost reading before and after the intercooler to see if it is losing pressure or anything. I haven't had the time or money to go source new intercooler pipes to chuck a nipple on and a boost gauge yet.

Time will tell :)

The graph looks similar to the turbo I got now on pump 98 td05h18g kando

http://nissansilvia.com/forums/index.php?showtopic=498401&st=90

If Hypergear could make something similar to the hksgt2530 I had I would get it fullboost by 3500rpm 20psi 180rwkw by 4000rpm on sr20 thats the most responsove setup ive had so far and ot drove the best And still made decent power on 21 dropping to 19psi 251rwkw e85 drives better than the setup i got now td05h18g e85 24 dropping to 21psi making 264rwkw

link to dyno graphs and comparisons are in the link above the power curves abit wobbly cause my boost solenoid was cactus

I think I might give his new billet ss1.5 ago seems like it should make similar power as the hks gt2530 and response his sspu is similar to the td05h18g I have now full boost 4000rpm 20psi and made similar power

Edited by hy_rpm

Stao has given me some good advice to check the boost reading before and after the intercooler to see if it is losing pressure or anything. I haven't had the time or money to go source new intercooler pipes to chuck a nipple on and a boost gauge yet.

Just make a manometer :) Will cost maybe $10 to make and will be far more accurate than any boost gauge you buy.

Also got my car back from tuning by C-Red today. I was a little sad panda when Mark said It made 335rwhp on 16psi (they say they have a low reading dyno). However it pulls hard once again, like it did with 375rwhp on 21psi last year, so im wrapped.

It didnt seem to like 20psi very much with lots of pinging, so timing had to be taken out a fair bit.

Taking it to the drags on wednesday to see what's what. ;)

Will remember to avoid C-red then :whistling:

WMI :) do eeet!!!

The graph looks similar to the turbo I got now on pump 98 td05h18g kando

http://nissansilvia....ic=498401&st=90

If Hypergear could make something similar to the hksgt2530 I had I would get it fullboost by 3500rpm 20psi 180rwkw by 4000rpm on sr20 thats the most responsove setup ive had so far and ot drove the best And still made decent power on 21 dropping to 19psi 251rwkw e85 drives better than the setup i got now td05h18g e85 24 dropping to 21psi making 264rwkw

link to dyno graphs and comparisons are in the link above the power curves abit wobbly cause my boost solenoid was cactus

I think I might give his new billet ss1.5 ago seems like it should make similar power as the hks gt2530 and response his sspu is similar to the td05h18g I have now full boost 4000rpm 20psi and made similar power

Shouldn't be an issue matching the 2530, The new billet SS1 might perform better within the same HP range.

The SS1PU is a larger turbo compare to T518Z, Per Abe's result its already sitting 265rwkws on Pump 98.

E85 results with 98 is not directly comparable, there is a 40kws difference in peek power as well as mid range.

If the SS1PU's peeking 248rwkws @ 18psi on pump 98 on at 45 degrees day. On E85 it should be pushing towards the 280rwkws mark with slightly better response. I'll be looking forward to the final E85 or P98 tune once his engine runs in.

Also response is pretty decent for a none VCT SR20det too.

Anyone heard of a 'Hybrid intercooler'? I must be lucky because it also says its limited edition haha

Most probably something cheap and this could be why I need 20psi to produce the same power as people running 16psi such as birds results.

I got a hybrid inter cooler kit fitted 10yrs ago for $1400

Have never tested drop across it

I got a hybrid inter cooler kit fitted 10yrs ago for $1400

Have never tested drop across it

Haha shit $1400

So in this day and age would they be significantly cheaper?

Once I get some pipes I'll check.

Should it be 0 boost drop or do most have at least a little?

Haha shit $1400

So in this day and age would they be significantly cheaper?

Once I get some pipes I'll check.

Should it be 0 boost drop or do most have at least a little?

Mine had 1psi on full load in 4th. Which in the scheme of things is fark all. Ideally you want 0, but 1-2psi is good too. It's when you're getting 5/6/7psi that you have an issue.

I'll send that PM soon dude, just sorting out the mrs ;)

Nah I have a pump 98 result in the link aswell

It's making 231rwkw on 19psi by 4200rpm on 20psi made 237rwkw

His one is 234-5rwkw on 19-20psi by 4000rpm if you read his graph

mines non VCt aswell same dyno same ramp rate same tuner

On a hot day it will boost up faster when it heat soaks but not make as much top end power as mine did that when the radiator was no good coolant temp was getting to 100•c on the dyno but I couldn't believe it full boost was 3600rpm once we let it cool down for 15mins power was back up 10kw and boost back at 4000rpm

If you overlay my td05h pump 98 dyno graph over his ss1pu one it's very similar

Abe's result you can't directly compare cause its a different dyno different tuner larger cams 272 duration 12mm lift and it 263rwkw at 19psi by 4250rpm

Mine and scotts results same tuner same dyno same cams poncams same boost

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...