Jump to content
SAU Community

Recommended Posts

12 hours ago, 4bidn1 said:

I should really put my glasses on before typing on my phone ?. 

Thats not even English 

I'm a full ching chong bing bong and my engrisher is better LOL

We sponsored topstages S14 for wtac this year, its an built sr20det with solid head and pro cams. Upgraded to our ATR43SAT turbocharger from Garrett GT3071. Car made more power through out the whole rev range and maxed at 381rwkws e85 fuel.

14500401_1188416121202317_74590799406876

 

Red: Atr43sat

Green: Gt3071

391rwkw.jpg

Philip island test run:

 

  • Like 1

Haha, the car had upgraded fuel pump later on so I upsized the turbo to an ATR45SAT which made 408rwkws on an aggressive tune. Backed to 399rwkws for tracks. It run 1.251 at Winston last week beating previous wtac winners result of 1.26

14542310_1188415847869011_41923078897209

14519735_1805987033011106_22834492266191

399rwkw.jpg

 

  • Like 3

I think 420rwkws is about the most this turbo can do. have to upsize wheels for more power. But Its plenty for what this car needs so far.

  • 3 weeks later...

Hi all.
I'm about to order the atr43sat for a 25. Looking to make 450-500rwhp Questions are:
Can that be had internally gated through standard dump?
If I need to change dump etc might as well go ex-gate yeah?

On 2016/5/16 at 0:42 PM, CEF33Y said:

Speaking of Non VCT, low cr engines, did you ever end up doing any development with an RB20 Tao?

There are so few of them around and took a while to find the right car. Picked up a 93 model R32 GTS4 in good mechanical order. Will be starting developments based on R32 Rb20det engines. My goal is to 270rwkws on pump 98 fuel with good turbo response.

gts4big.jpg

Car is pretty basic with a return flow cooler, and a turbo back exhaust fitted. I will be Nistune it and drop in some ID injectors for starters. I will list prices and places as project move along.

  • Like 2

haha true, my plain is to drop in a RB25det NEO motor off a Stagea in it later on, Nissan should've done that years ago.

I will be using our ATR43SS1 as well as doing some high flows, and see if there are room for improvements.

  • Like 2

Will be moving to a new ATR45SAT Ball Bearing soon.
Will put results up here once dynoed.
Below is what im going from -> to.

ATR43SS2+ gate off housing - > ATR45SAT BB
Stock ExhaustMani - > D2 Stable High Mount + Gate of mani
44mm Tial Gate - > 50mm Turbosmart Gate
Stock Plenum - > Custom FFP + Sard Fuel Reg
Single 460 Walbro - > Probably Surge tank
Nistune ECU - > Adaptronic ECU +Wideband/Airtemp sensor
Z32 AFM - > MAP inside adaptronic
E85 - > Still E85
Stock Head - > Only doing ARP headbolts
And a bunch of other random stuff

Was ~450 hp at the rears - > Hoping for + 550 hp at the rears

Current full boost is around 3800 @ 20-21 psi
Im hoping for similar response, looks like it will be close.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...