Jump to content
SAU Community

Recommended Posts

Thanks mate!

Ron: the SR is good for about that 280-300kw mark. Its just about control factors. If on 98 a little ping will do a lot of pop at that level, but if tuned safely (like on E85) they are pretty OK.

For reference my 'built motor' is nothing but a refreshed stocker with forged pistons. Im reusing the crank and rods and aiming for a motor that will never see more than 350 even if I do go crazy in the long run. It will probably never see over 300 in reality.

Because the last tune was close to 430 RWKW. Different head and a few different mods I wanna see what these little things can do. They should crack 450 without too much trouble.

-5's aren't too bad, A Z32 at Unique Autosports just cracked 447rwkw on 21psi and pump fuel with them.

are you saying someone nearly cracked 600rwhp with -5's at 21psi ??

From what he's said he has 3" Intakes on the turbos but they are run of the mill -5's apart from that.

http://www.aus300zx....2&postcount=358

Edited by Super Drager

Thanks mate!

Ron: the SR is good for about that 280-300kw mark. Its just about control factors. If on 98 a little ping will do a lot of pop at that level, but if tuned safely (like on E85) they are pretty OK.

For reference my 'built motor' is nothing but a refreshed stocker with forged pistons. Im reusing the crank and rods and aiming for a motor that will never see more than 350 even if I do go crazy in the long run. It will probably never see over 300 in reality.

Should go a td06sl2 20g 8 cm but with billet compressor wheels

Transistient boost response will be better and get maybe 10kw more up top

Hypergear can get them or gtpumps or you can get kando to make one as kamak is making billet compressor wheels now and kando get there turbos from them

From what he's said he has 3" Intakes on the turbos but they are run of the mill -5's apart from that.

http://www.aus300zx....2&postcount=358

I think you'll find they're 2871R's or -10's from my conversations with John from Uas who is building on it.

Could have misunderstood though.

I think you'll find they're 2871R's or -10's from my conversations with John from Uas who is building on it.

Could have misunderstood though.

Nope, take a look at the thread i posted. GT2860-5's. There is a Z32 that was built with GT2871R's though, he put down 467rwkw.

Should go a td06sl2 20g 8 cm but with billet compressor wheels

Transistient boost response will be better and get maybe 10kw more up top

Hypergear can get them or gtpumps or you can get kando to make one as kamak is making billet compressor wheels now and kando get there turbos from them

Have you seen any results of any of the above turbos vs billet wheeled versions?

my PT6262 .84 TS will be arriving this week hopefully, should in interesting. I havnt seen anyones results on this forum using one with this setup (25/30 with vct).. should be neck breakingly responsive ;), and if it taps out too early, well.. only $285 for the 1.0 housing to be sent to replace the 84 and try again.

my PT6262 .84 TS will be arriving this week hopefully, should in interesting. I havnt seen anyones results on this forum using one with this setup (25/30 with vct).. should be neck breakingly responsive ;), and if it taps out too early, well.. only $285 for the 1.0 housing to be sent to replace the 84 and try again.

Eagerly waiting results as this was the same path I wanted to go down! :) Built motor? Is the 6262 Gunna be pushed hard mate?

Have you seen any results of any of the above turbos vs billet wheeled versions?

Just had a result sent in from a SR20det customer made 282rwkws. That is our billet version, don't want to hijack the thread, check out dyno readings on my thread.

I have a billet 7175 (.94 single entry) on a single cam rb30. With a powerglide.

It's as responsive if not slightly better than a 35r (1.0x). Makes 549hp@28psi on e85. Trapped 138mph. Keen to feed it proper boost soon and see how it goes :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...