Jump to content
SAU Community

Recommended Posts

I have been reading up on some of the regulations and items included as factory options can be run on the car provided they are included in the homologation documents that were submitted for the car or are included in factory option brouchers.

I have recently obtained a factory options broucher that covers R33 GTS25T Series II and GTR's.

The obvious items on your car are the side skirts and the front Nismo lip that were factory options. The GTR adjustable rear wing was also a factory option that may provide some improved aero over a stardard Series II wing at speed.

If you are interested I can scan the broucher and email it to you if you have any difficulties with CAMS or other officials.

I weighed petes car a couple of weeks back. I ran out of weights trying to substitute him.......

It wasn't overly heavy for a GTR.

I rekon neil's will come in around the 1300kg mark.

I think mine came it at around 1370 kg full of fuel at EC's weigh bridge, don't know how accurate they are though.

I have been reading up on some of the regulations and items included as factory options can be run on the car provided they are included in the homologation documents that were submitted for the car or are included in factory option brouchers.

I have recently obtained a factory options broucher that covers R33 GTS25T Series II and GTR's.

The obvious items on your car are the side skirts and the front Nismo lip that were factory options. The GTR adjustable rear wing was also a factory option that may provide some improved aero over a stardard Series II wing at speed.

If you are interested I can scan the broucher and email it to you if you have any difficulties with CAMS or other officials.

Thanks Charles that would be very cool,,,even just for the look see. Sorry mate I have no side skirts and my lip is M spec not Nismo.

I'm a firm beleiver that if a part is listed for fitment as an accessory or option by the manufacturer or it's race arm then it should be allowed to be used. Unfortunately I think CAMS see it differently.

Brad,,,I weigh 72 kilo's so please no setting up for Larger Gents and Cheryl has had no real weight reduction yet,,,she still has her intrusion bars.

Cheers

Neil.

She comes in at 1295kg with the screens fitted.

Same condition as when you dropped it off Neil.

It has a 50.52% (drivers side front biased) diagonal split with a 70kg driver ballast.

59.6% front heavy which is typical. Front being 769kg's

I've got center of gravity heights and roll couple heights for you as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...