Jump to content
SAU Community

Recommended Posts

Ripped Aaron's turbo out, 2 hours flat. Not bad going.

He is going for a bush core this time as bearings have left a bad taste in his exhaust, and bits of wheel. Shaft snapped in half.

Don't want to sound sceptical, but can you prove the increase in driveability, economy and reduction of intake temps?

This argument has been done to death.:whistling:

Back to back, same day, plenum skin temp measured with a non contact temp gun (accurate to 800deg) 31deg reduction.

Economy; only .1-.2 km/l, possibly a bit more.

Driveability; VERY subjective, because it's a "seat of the pants thing". But; Yes, farking HEAPS! Better response, stacks more torque.

Ripped Aaron's turbo out, 2 hours flat. Not bad going.

He is going for a bush core this time as bearings have left a bad taste in his exhaust, and bits of wheel. Shaft snapped in half.

DUDE! i have to give scott the biggest props for doing this!! had the turbo out in 2 hours! and managed to get it fixed under warranty..

stage 2 wheels bush bearing core!

cant wait now.

f*kn owe you one scott!thanks.gif

8psi. lol. Not even tuned, second gear apparently at 2000 revs. The bearings were noisy when it first went in, after 3 months it had snapped the shaft and demolished the exhaust wheel, front looked pretty good considering but it was seized.

I had the car on stands, its an easy job if there is no heat-shield so guess what's not going back on. lol. 3m stick-on heat-shield will do the job nicely. :thumbsup:

yeh 2nd gear at about 2k revs. i was behind someone going slow so i wasnt even pushing it.. i mean it was 6am.. i was tired. then bang black smoke. that woke me up good.

hasnt been in the car for even half a year..

n yeh ive turned the boost right down as it wasnt tuned yet..

I don't really want to dob the shop in as he is looking after us with a warranty, it was a ball bearing highflow though.

Due to the damage to the housings it looks like he is going bigger than mine.

Nice, how do you plan to get it running?

I still think its a downgrade unless you go forged internals...

You are suffocating the engine if that has the stock turbo on it. You will be on boost at idle. lol.

The engine will be built, and it will run a bigger turbo.

Firstly though, I need to sort out the EMS and get a manual conversion happening. My tuner tried on the Haltech and said it isn't compatible, something to do with the pulses, I forget what exactly.

Has anyone made any headway in manual conversions for the M35?

Is the R34 GTR gearbox with bellhousing modifications the go?

The engine will be built, and it will run a bigger turbo.

Firstly though, I need to sort out the EMS and get a manual conversion happening. My tuner tried on the Haltech and said it isn't compatible, something to do with the pulses, I forget what exactly.

Has anyone made any headway in manual conversions for the M35?

Is the R34 GTR gearbox with bellhousing modifications the go?

Im about to go down this path myself but I think I will hold off on my 3.5 build for now for the very reason you are having now, people dont understand these engines. You will have to go standalone, PS2000 or motec m800 or similar which means you may not have the dash, attessa abs etc. Will you be paying a mechanic to learn all about this engine?

Pulses? I guess he means the crank sensor? Better find a new tuner... What Haltech was he using anyway?

What prompted this change over? Did you damage your engine? Do you still have it?

lol... you don't sound sceptical at all!

Point taken. I have just been on a few forums where people fit stuff, then say how good it is without hard data. I can't really 'feel' your 'seat of the pants' performance upgrade.

Just want numbers that's all.

This argument has been done to death.:whistling:

Back to back, same day, plenum skin temp measured with a non contact temp gun (accurate to 800deg) 31deg reduction.

Economy; only .1-.2 km/l, possibly a bit more.

Driveability; VERY subjective, because it's a "seat of the pants thing". But; Yes, farking HEAPS! Better response, stacks more torque.

Thanks Daleo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...