Jump to content
SAU Community

Recommended Posts

Got the following completed today ready for wheels tomorrow

- changed oil and filter

- replaced front inner passenger guard (grill due to transmission cooler in fro t of it to let heat excape)

- cleaned engine bay

- put the lower stone guards back under the front of the car

- finished securing Axis kit

- painted R34gtt front calipers black (yet to do silver 'NISSAN' writing

- placed spacer on exhaust so it clears kit70fba96b223414a91bfb5704af408dfb.jpge7176bddd3f9a300371b941f1c27eded.jpgdfb4aa956456a135d743585ef51abea3.jpg96f12d9fe38c063b4231f25877508790.jpg2a6161fa8529800f6a2d8ed588807374.jpg

Inspiration ..... added my to do list, the transmission cooler that is. Did you write up a diy somewhere?

Joined the Aero club, well in the front anyway..

Cut out the backs of the blank inserts to let air in, and to show off the polish pipe :)

That's it, I've finished her, and don't give me any more ideas.

post-25026-0-45012400-1466912022_thumb.jpg

post-25026-0-72554200-1466912033_thumb.jpg

post-25026-0-97534800-1466912127_thumb.jpg

post-25026-0-37946300-1466912148_thumb.jpg

  • Like 1

Joined the Aero club, well in the front anyway..

Cut out the backs of the blank inserts to let air in, and to show off the polish pipe :)

That's it, I've finished her, and don't give me any more ideas.

Either black out, or nip out the centre support in the meshed area (below the numberplate); it really cleans the bar up IMO.

The mesh and undertray are more than enough to support the opening without that spar.

13439023_10154287317847392_4871370956259

Joined the Aero club, well in the front anyway..

Cut out the backs of the blank inserts to let air in, and to show off the polish pipe :)

That's it, I've finished her, and don't give me any more ideas.

Painter did an awesome job with the matching. I was considering doing this to the blanks when i had it but these are too hard to find another set off did t want to ruin them at the time.

Looking good man for sure.

Checking battery voltage as bike one playing up lately. 12.2V before starting, charging at 14.4-14.6V, about 13 after shutdown, all good for now. Cranks over fine but we getting into cold weather now its not being used every day.

MY02 tyres at 5mm & 6mm after about 19500km, had them rotated at WOF time just because it was free. Wearing nice and evenly.

Didn't need a rebalance like the shop guy tried to sell me, have always done my own in past and no problems.

post-119976-0-65539500-1467336753_thumb.jpg

  • 2 weeks later...

not much. I took off the emblems.

adhesive had a hard time getting away. had to grind finally got that bulges out

 

yet another label but later removed

 

20160710_191259_HDR.jpg

Edited by TukeH
11 hours ago, TukeH said:

not much. I took off the emblems.

adhesive had a hard time getting away. had to grind finally got that bulges out

 

yet another label but later removed

 

20160710_191259_HDR.jpg

 

mahtava

 

  • Like 1
44 minutes ago, yuma said:

Finally got mine from compliance and got it regoed today. So damn happy with it. Gonna have to roll the rear fenders but. 2dacabbba7e70a8f84d768fe718b240a.jpg

539f1a3ceb10818d3da6de588205f78a.jpg

350rx black with black leather.

very nice indeed, north or south?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...