What Have You Done To Your Stagea Lately?

[West]

Got the following completed today ready for wheels tomorrow

- changed oil and filter

- replaced front inner passenger guard (grill due to transmission cooler in fro t of it to let heat excape)

- cleaned engine bay

- put the lower stone guards back under the front of the car

- finished securing Axis kit

- painted R34gtt front calipers black (yet to do silver 'NISSAN' writing

- placed spacer on exhaust so it clears kit

Inspiration ..... added my to do list, the transmission cooler that is. Did you write up a diy somewhere?

[joshm35]

Ill tag you in the post on facebook.

[iamhe77]

Trans cooler install looks nice, concerned about mud/water spray from the wheel?

[ebellis]

dropping it off tomorrow to get this installed, may go ahead and replace the accumulator while I'm at it

[joshm35]

Trans cooler install looks nice, concerned about mud/water spray from the wheel?

Nah. Haven't had any issues with it yet. Grill is small enough to keep the mud out.

[joshm35]

Wheels installed and brakes painted

[West]

Wheels installed and brakes painted

Need some shiny Gold Brembo to look the part

[joshm35]

Need some shiny Gold Brembo to look the part

These will do

[conan7772]

Joined the Aero club, well in the front anyway..

Cut out the backs of the blank inserts to let air in, and to show off the polish pipe

That's it, I've finished her, and don't give me any more ideas.

[Daleo]

Joined the Aero club, well in the front anyway..

Cut out the backs of the blank inserts to let air in, and to show off the polish pipe

That's it, I've finished her, and don't give me any more ideas.

Either black out, or nip out the centre support in the meshed area (below the numberplate); it really cleans the bar up IMO.

The mesh and undertray are more than enough to support the opening without that spar.

[joshm35]

Joined the Aero club, well in the front anyway..

Cut out the backs of the blank inserts to let air in, and to show off the polish pipe

That's it, I've finished her, and don't give me any more ideas.

Painter did an awesome job with the matching. I was considering doing this to the blanks when i had it but these are too hard to find another set off did t want to ruin them at the time.

Looking good man for sure.

[joshm35]

Gave her a detail for the Happy Laps track day out at Lakeside. (Photos thanks to Tim 4020 Media).

[joshm35]

A bit of heat tape lovin

[NZM35NZ]

Checking battery voltage as bike one playing up lately. 12.2V before starting, charging at 14.4-14.6V, about 13 after shutdown, all good for now. Cranks over fine but we getting into cold weather now its not being used every day.

MY02 tyres at 5mm & 6mm after about 19500km, had them rotated at WOF time just because it was free. Wearing nice and evenly.

Didn't need a rebalance like the shop guy tried to sell me, have always done my own in past and no problems.

[TukeH]

not much. I took off the emblems.

adhesive had a hard time getting away. had to grind finally got that bulges out

 

yet another label but later removed

 

Edited July 10, 2016 by TukeH

[datmoo]

11 hours ago, TukeH said:

not much. I took off the emblems.

adhesive had a hard time getting away. had to grind finally got that bulges out

 

yet another label but later removed

 

 

mahtava

 

[yuma]

Finally got mine from compliance and got it regoed today. So damn happy with it. Gonna have to roll the rear fenders but.



350rx black with black leather.

[stripey]

44 minutes ago, yuma said:

Finally got mine from compliance and got it regoed today. So damn happy with it. Gonna have to roll the rear fenders but.



350rx black with black leather.

very nice indeed, north or south?

[yuma]

Up in Launceston mate.

[conan7772]

Yep blacked out the centre brace on the front bumper with some carbon wrap.

Looks way better.

 

Edited July 13, 2016 by conan7772