Jump to content
SAU Community

Recommended Posts

Unfortunately the new custom sump was modelled on an R33 and it didn't clear the swaybar enough when we put it in last week.

Because of this we missed out at PI on the weekend. I had brand new rubber on the thing and was ready to go but no such luck...

Turns out that the whiteline sway bar that is on my car was a prototype from years ago and they don't sell them anymore so pretty unique situation. The bend is very close to the sump so that's what has caused the issue. I think that a new 27mm sway bar with a better option that pulling the sump off again! Custom one being investigated now. Hope it makes the 21st!!

  • 2 weeks later...

time for another update...

New 27mm swaybar has just arrived to solve the sump clearance issues. I currently have a loan 24mm until I get a chance to fit the 27mm. Might try both on the weekend if I can as a comparison.

Fulcrum suspension have sorted out the bar for me.

I've extended the wing end plates as the old ones were a little small and the bigger ones should hopefully stop a bit of the spill over the sides.

post-10715-0-12315400-1342526396_thumb.jpg

The splitter has come a long way. I'm still testing as it's all a bit new to me still. I'm really just copying what the fast guys do and following basic principles and advice I'm getting along the way.

I'll be logging the data at Philip Island this weekend to see if straight line speed is sacrificed and if corner speed is increased. As a bare minimum I'm expecting more downforce from just the splitter seperating the air and minimising air flow under the car.

If it all works the plan is to make the parts out of carbon fibre down the track. It's all trial and error at the moment.

post-10715-0-15594600-1342526630_thumb.jpg

post-10715-0-67829500-1342526762_thumb.jpg

post-10715-0-83309300-1342526985_thumb.jpg

loving the alloy canards. i made some about 3 years ago and was laughed at. been hesitant to make any new ones.

i seen in a build thread for an american R35 time attack car they made canards out of alloy. they were far easier and cheaper and did the same job.

are the uprights for your wing an off the shelf item?

Yeah the ally is pretty light except for the splitter. It's damn heavy. CF would be so much better

are the uprights for your wing an off the shelf item?

Nah they were made by superleggera carbon fibre in sydney. They're pretty hard core!

Yeah the ally is pretty light except for the splitter. It's damn heavy. CF would be so much better

Nah they were made by superleggera carbon fibre in sydney. They're pretty hard core!

oh they look like a production type thing.

do you have any bracing under the boot lid? i may have missed it.

Hope you don't mind Russ. Most people probably know what happened already!

Russmans R32 GTST blasting around PI in it's last shakedown before WTAC!

For the full article check out Autocult -> CLICK HERE!

7629603330_b9209c015b_b.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...