Jump to content
SAU Community

Recommended Posts

  • Replies 204
  • Created
  • Last Reply

Top Posters In This Topic

Thanks gregor for the tips. On last check my tyres were 36 psi so I take it the global advice would be to drop this figure to close to 30 all round, to be checked after the first session.

I'm going to print a "don't use the handbrake" sign - that's one habit it is going to be hard to break.

So, anyone driving down at 5:30am on Sat morning??

I am leaving Campbelltown around 5am if you can manage that. Me = slow driver.

I am leaving Campbelltown around 5am if you can manage that. Me = slow driver.

wow..too early for me to manage. with a bit of luck i will be coming thru Campbelltown by 5:30. Even at 'slow' surely it's only 1h 45m from C'town?

I'll have to disagree with gregor... I found a higher tyre pressure on street tyres works well as street tyres do not have as reinforced sidewalls as semi slicks. This should reduce tyre wall flex which is important as you are going to be a lot harder on your tyre's sidewalls than if you were on the street.

I haven't used street tyres on my Skyline for a while now, but when I did I kept my tyre pressures around the 36psi cold mark, then at the track bump them up to around 38-40. After a session I would set them at around 41-42psi hot... but that was when they were well and truly overheated and didn't want to grip the track anymore and you want to avoid doing this too much as it degrades the rubber. This may seem high, but my tyre wear was still consistent with under inflation (and/or someone who uses the steering wheel as a brake of sorts :blush:)

My previous comment still stands, focus on getting consistent (not to be confused with fast) lap times before trying to change too much with the car ;)

EDIT

Asking about tyre pressures is relatable to asking how long a peice of string is :laugh:

I dont think our approaches are too different but perhaps i wasnt as clear as I intended. When I go to the track I usually stay at goulburn the night before and if possible trailer my car - as a result the tyres are cold or at least cool by the time the first session rolls around. If you run pressures in the mid 30s cold for normal use then you can expect them to shoot up more so than when street driving when you hit the track. 10 psi was probably an over statement but taking off 5 psi cold would help get you towards the 41-42 psi hot target you mentioned. With normal street pressures (36 in my xr6t) i found the car was very slippery and that the pressures had gone up alot.

So for the guy who asked - keep an eye on your pressures after each session and adjust if you think its needed.

So for the guy who asked - keep an eye on your pressures after each session and adjust if you think its needed.

Sound advice, thank you. Just out of interest, will there be people with air compressors willing to share with us noobs so we can pump our tyres if needed?

CUT-CORNERS-650x433.jpg

That's just how I roll :P

Sound advice, thank you. Just out of interest, will there be people with air compressors willing to share with us noobs so we can pump our tyres if needed?

There is one at Wakefield, but it isn't very good... if I remember to bring mine I'll let you borrow it ;)

ahaha because race car indeed!

weather looks great for turbos....sunny and 10.

I'm not running the race car this time, but I will be available for anyone who wants some pointers on track driving - I will be near the flag point so just grab me.

yeah its a bit of a pain but I just don't have the space to fix it while i am building the house. Pretty sure tk80 is out too....cage is half finished :(

On the good side dnissi will be there to keep them honest....he was only a tenth behind me all day and I'm sure will be looking to go faster this time.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...