Jump to content
SAU Community

Recommended Posts

Well, I drilled holes in one of the manifolds last night; so it may never run again...

Hope everything went smoothly today, and that Craig didn't have a protein shake for brekky; too much powaaaahhhh!

Finished for today. We're both stuffed.Manifolds on, crossover pipe , heat shield on. Turbo on and tight. Intake on. O2 sensors on and heat proofing in lots of places. Oil and water feeds to turbo done, have to do returns. Need to fabricate turbo outlet piping, and exhaust from where the gate goes in needs to be extended. I'll post some pics tomorrow when I'm not exhausted!

Big thanks to Craig for putting in the lions share of work, and Dale for fixing up a boo boo last night, even at a BBQ! Both legends, and can't thank you guys enough. cheers.gif

On a note, never put your hand up to change v35/350z headers, not in a million years!

When attempting difficult jobs, its important to be precise and organised....

6661998321_8f5a00e1b4.jpg

6662005899_f2b72a7caa.jpg

Trial fit

6662011939_57b2899850.jpg

Is it getting heavy yet? I'll just take moar pics....

6662017203_8c93b1982b.jpg

The Manifold- couldn't fit a fart up there its so tight...

6662022045_f2c9b5476e.jpg

Ready for a manifold on the drivers side- Except this one has a bit of Daleo Magic in it!

6662027853_fb95125f05.jpg

6662034237_c6964508ce.jpg

Craigs fav. work-zone: Turbo, gate, washers and beercheers.gif

6662040867_a693b0366c.jpg

Looking a bit bare...

6662047943_68e9b7381a.jpg

What turbo officer...?

6662054531_43cfa868d0.jpg

That ends it for now.

you didnt drop the engine to install the manifolds???

nup......I have cuts and abrasions to prove it!

IMO theres about 5 hours of work left.....tops!

not including the 2 bits of custom stuff that needs doing

Edited by Jetwreck

lolz.........we not only have 1 hoist.....we have 2 at Stagea Garage! nyaanyaa.gif

Bah! Weak!!

Or perhaps I am a touch jealous of not having to lie under the car holding the exhaust in one hand whilst doing up nuts with the other....

Scott removes NM35 turbo's without a hoist or removing the engine quite often.

You won't be able to remove the turbo and manifold as one. The turbo will need to come out, then the manifold

Edited by iamhe77

Does that mean then you could remover the turbo from an NM35 without engine out? Is it possible if its turbo and manifold in one?

yes it does....every turbo I have done has been with the motor in the car. However I did my turbo while the motor was out and it was so much easier.......I am actually going to trial just removing the Crossmember this weekend coming on a NM35......his got the same turbo as me so it's a little more fiddly so I probably wont get it done is 2 hours like Scott can apparently do!....I estimate about 10 hours!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
×
×
  • Create New...