Jump to content
SAU Community

Recommended Posts

thats awesome, making me want to buy a supersport but i don't ride enough..

I'd go for a 750, best of both worlds.. good power and not as bad on fuel as 1lt when i'm on my bike anyway it feels enough like a GSXR to me, close enough <3

JAIME, they're BN Blister copies

Ah ok cool!

Jamie, my bad.

Jayme, scarnon brah?

LOL!

Yeah good thanks Bird man!

Lol, dare say there was some slight bias in the judging, good to know adz wants my mrs..........

It'd be hard to say no... :)

e4.jpg

yamaha_r1_white_transformer_24.jpgyamaha_r1_white_transformer_22.jpg

Would look like, how a Decepticon Motorbike would be.

thats awesome, making me want to buy a supersport but i don't ride enough..

I'd go for a 750, best of both worlds.. good power and not as bad on fuel as 1lt when i'm on my bike anyway it feels enough like a GSXR to me, close enough <3

Your logic is fallible...people who seldom ride should buy a supersport cause the harshness won't bother you like it would if you were commuting on it. If I could fit on a 600 I'd buy one for the economy, but the torque of a litre bike is such an awesome thing in the traffic...you changed gears twice while I was still in 1st lol :P

Thread locked?

That's a bit homosexual

I was gonna submit nudez

Same.

Your logic is fallible...people who seldom ride should buy a supersport cause the harshness won't bother you like it would if you were commuting on it. If I could fit on a 600 I'd buy one for the economy, but the torque of a litre bike is such an awesome thing in the traffic...you changed gears twice while I was still in 1st lol :P

Same.

lol my first only goes to 85 i think :(

Single swing arm looks epic but I'd be worried about the flex on the remaining arm?

If it's been done properly they will have reinforced the remaining arm or replaced it with a bigger one, though looking at the picture it doesn't look like it. The 1098 has a single swing arm and it's fkn huge. Notice how the swing arm bends and the wheel is offset to maintain balance.

Ducati%201098%20%201.jpg

lol my first only goes to 85 i think :(

1st on my virago went to 45, 50 if I redlined it lol. If I keep my bike long enough I'll get a sprocket set for it, long 1st is lazy but you're breaking most speed limits just to be on-cam.

My mate has a 600 gixxer, told me to get the 750 as it's the same size bike but doesn't need to be worked as hard when cruising... My 250 is revving it's dick off at 100 in top gear so I'll be looking forward to a more cruise feeling when I upgrade

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...