Jump to content
SAU Community

Recommended Posts

yar yar. i confused myself a bit in my post. He said he would need "ID1600" for 400hp, which would be "maxing them out" (in his mind 400cc per injector). We were all wtf, because 1600 more than enough for 400hp. Turns out he meant ID400. Got that stubborn mind where when someone states xxxCC injector, thats the overall CC for the whole engine. Lol

facepalm.... please never talk about injectors again... my head can take only so much

The guy that used to own that car

i lol'd

social engineering 101. Need to take advantage of sau cred and/or strong referral for maximum response.

Aint no body got time for random unknown emails/calls

No you don't...

Ain't no body got time for random unknown emails? Aaron does, he's running a business.

Either PM him on Facebook, email him or call him.

If you're interested in doing business with him, he's interested in doing business with you, or Import Monster would have gone bankrupt years ago.

No you don't...

Ain't no body got time for random unknown emails? Aaron does, he's running a business.

Either PM him on Facebook, email him or call him.

If you're interested in doing business with him, he's interested in doing business with you, or Import Monster would have gone bankrupt years ago.

Yup and that's why I'm looking for a direct contact to him as opposed to a generic email address :)

FWIW import monster cust service is impeccable

I emailed them on the support @ import monster or whatever address, not to buy shit, but to get my money back as I had excess funds in my account.

I got a return email within the hour and the funds deposited then and there. available in my acct the NEXT DAY

suck it up and email him the way he want's you to unless you need to have a lengthy chat about importing a car

When people say they need to run 1000cc injectors for xxxHP. that means 1000cc each injector right...?

Some noob on ozhonda keeps saying that when people say 400cc is needed for 400hp on E85 on a 1.8L 4cyl. He thinks that its 100cc injector per cylinder...

So he says he needs 1600cc injectors for 400hp e85 n/a, which in his mind means 400cc each injector. Lmao, confews...

Honda people i swear...

941507_516431031746010_342994890_n.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...