Jump to content
SAU Community

Recommended Posts

Could probably report the plates to the ethical department if you could be bothered

what so they deny it, nothing happens to them and then i DEFINITELY end up with a defect/EPA

lol no thanks

Ontopic:

The amount of RIP Paul Walker crap on ebay is astonishing. who is buying this crap??

http://www.ebay.com.au/itm/Paul-Walker-The-Fast-And-The-Furious-100-Cotton-Enzyme-White-Mens-Tee-TShirt-/261346483497

http://www.ebay.com.au/itm/RIDE-OR-DIE-MOTORSPORT-Mens-TShirt-TEE-tribute-PAUL-WALKER-FAST-AND-FURIOUS-T-/171198430454

also ontopic:

Saw a divvey van on maroondah hwy today who obvious left the rear capony hatch and side canopy windows open because they were driving with them all open. spastics. takes like 50m of road to realise "why is everything so clear out my rear vision mirror...?"

also ontopic:

Pulsar made in australia. doesnt get the wimminz.

We all know what happens to complaints made about cops. If you don't have it on camera, good luck.

Remember when Pettett had a hatebook page? The police commissioner described him as a model officer with no record of complaint filed against him...to his knowledge. Lost faith in entire force that day.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...