Jump to content
SAU Community

Recommended Posts

#@r34abz mate, as long as you don't have an inter-cooler with that pod, it's fine. As Alvin said, one intake mod is ok and if you've got everything stock you'll pass. EPA's are the reason I don't want to get an aftermarket exhaust.

  • Like 1

Check out this Mitsubishi Lancer.

http://www.carsales.com.au/private/details/Mitsubishi-Lancer-2001/SSE-AD-2839584

Nick is this yours?

Nope, mine sold on fleabay not long ago for $12k, un-regod, no rwc, recent engine swap, shit condition car overall and still had the jdm-007 plates

bit steep, are they forged? I got brand new TE37's for a little bit more than that...

I have no idea what my stud pattern is, what widths/offsets I'd need etc.. haven't looked into anything yet

pcd is 5x120 so same as bmw

however not sure on offset, would need to pull a front and rear to check if stamped on inside, if not need to measure and calculate

measure the exact width of th rim, from outer edge to outer edge (may have to lay it down and go with a tape from a flat surface from bottom to top as it's got tyres)

then measure from wheel hub to the lip on the rear

take the first measurement (lip to lip) and divide into 2

then take second measurement (hub to lip) and minus the first measurement from that

Meisters are rad. Sort it out Leroy Jenkins

LEROYYYY JENNNNKIIIIINNNNNNSSSSSSSSSSSSSSSSSSSSSSSS

bit steep, are they forged? I got brand new TE37's for a little bit more than that...

I have no idea what my stud pattern is, what widths/offsets I'd need etc.. haven't looked into anything yet

Not forged, good luck finding good forged rims in these type of sizes for anywhere near this sort of money though ;)

Sure, if you ran pulsar sizes you could buy TE37s cheap.

:D

Green shell killshot just before the finish line is the finest play in the Mario kart book

there is a decidedly real satisfaction from sniping with green shells

but i was foreveralone playing with computer

Nope, mine sold on fleabay not long ago for $12k, un-regod, no rwc, recent engine swap, shit condition car overall and still had the jdm-007 plates

pcd is 5x120 so same as bmw

however not sure on offset, would need to pull a front and rear to check if stamped on inside, if not need to measure and calculate

measure the exact width of th rim, from outer edge to outer edge (may have to lay it down and go with a tape from a flat surface from bottom to top as it's got tyres)

then measure from wheel hub to the lip on the rear

take the first measurement (lip to lip) and divide into 2

then take second measurement (hub to lip) and minus the first measurement from that

LEROYYYY JENNNNKIIIIINNNNNNSSSSSSSSSSSSSSSSSSSSSSSS

Way too much effort. I'm sure it's on the internet..

Pretty sure it's just 2010+ models with power to weight of < 130 kW/t

Anything older will continue to be banned as per current rules / power to weight

I think you may be able to get a Golf R now. Saw some talk of this. Definitely the GTi I think?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...