Jump to content
SAU Community

Recommended Posts

It is what it is. They could probably double the price and still fill the field.

Its just capitalism at work.

As a spectacle it worth every cent. The best collection of wild imports in the southern hemisphere on display make it a not to be missed event on my calender.

  • Replies 742
  • Created
  • Last Reply

Top Posters In This Topic

They should line them up for a 5 lap race! That would be a spectacle. The Superlap thing can be quali :)

But agree, with regards to entry the event certainly isnt for everyone. But as a punter it will be a good weekend/spectacle. I just hope the local lads can get some meaningful kms on their cars during the year and take it to the blow ins :)

$1200 is pretty damn expensive for 2 days but it's the spectical and atmosphere (hype) that makes it so good. Better start saving my pennies and keep the development happening! It's not that far away!

You entering Boxhead?

Club Sprint.

It's an expencive weekend though from Vic.

Sure is but so worth it!

So entry, tyres, fuel, accom etc or another OS car holiday? Hmmmm, I doubt my car would make it throught he fashion police requirement anyway :)

I have only attended the first Oran Park event so would love to spectate and barrack for Russ in his cheater spec GTSt :thumbsup:

What do yo mean cheater spec??? haha It's the same as your car only wider!

Don't you go just for the drifting Noel?

BAHAHAHAHA :rofl::rofl:

The price increase was inline with something about more track time wasn't it?

Yet the schedule/timing looks exactly the same... :mellow:

Yeh, more track time...but same number of sessions?!? errrrr?

Less cars on the track....was that a real issue last year?

Don't understandy, I'll be there in some capacity anyway. If I'm going to lay down 3-4 track days entry for a single event is something

to be seen.

i am surprised noone has jumped on the bandwagon about the entry date and conditions of entry that have been posted up yesterday?

http://www.worldtimeattack.com/index.php/important-competitor-information/

Its an improvement, but I don't think it goes far enough. They should be accepting entries based on how fast their car is, not on how fast their entry form is.

Its an improvement, but I don't think it goes far enough. They should be accepting entries based on how fast their car is, not on how fast their entry form is.

Some sort of pre qualifier? Based on natsoft times?

I can see the merit for Pro. But Open and Club...not sure.

based on natsoft times done in the last 12 months... It wouldn't be too hard to work out what reasonably fast times are for interstate tracks. Particularly now that we've had a couple of WTAC events - you can easily compare who did what at EC WTAC to what they do at their home tracks...

People are paying to get in to watch this event, and there's more demand than supply for positions. Why shouldn't we see the fastest cars. Who wants to pay to watch a 2min Clubsprint car, or mid 50's Open Class cars when faster cars miss out just because they didn't get their entry form in within an hour of entries opening?

Edited by hrd-hr30

based on natsoft times done in the last 12 months... It wouldn't be too hard to work out what reasonably fast times are for interstate tracks. Particularly now that we've had a couple of WTAC events - you can easily compare who did what at EC WTAC to what they do at their home tracks...

People are paying to get in to watch this event, and there's more demand than supply for positions. Why shouldn't we see the fastest cars. Who wants to pay to watch a 2min Clubsprint car, or mid 50's Open Class cars when faster cars miss out just because they didn't get their entry form in within an hour of entries opening?

100% agree, for open class and club, its not even worth paying to watch if its just another supersprint, it should be the best of the best, therr are plenty of fast cars and fast drivers out there, it would be a pity for them to miss out because a average car and driver kept them out because their entry fee was in before them.

I hope the T shirts are better than the last 2 years, my 2009 one is still good but the 2010 one lasted about a week before the print fell off, I couldn't find any for 2011.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...