Jump to content
SAU Community

Recommended Posts

4 hours ago, Dose Pipe Sutututu said:

Is this your car?

https://www.gumtree.com.au/s-ad/wahroonga/cars-vans-utes/2002-nissan-s15-200sx/1251512935

I guess I was wrong with the Samsonas and the power, but 506kW was close enough.

image.png.7955f677222e9705a65d51c5dbb47d5a.png

506kW..."Never thrashed or abused" LOL

$75,000... double LOL

 

  • Haha 1

It’s running. Starter motor was buggered, new one has been installed and a new TPS also.

Dyno on Friday I’m dropping off 100L of fuel tomorrow and 3 canisters of NOS , gonna need a 200 shot to make the numbers 

6 minutes ago, acsplit said:

Scott's Dyno magically kills starter motors.

 

*Looks at the emtron fanboy with his gtr*

& Racepace kills motors, pls.

Emtron is #1, move over Motec there is a new playa in town.

Once i started boasting about them online years ago before I even ran one everyone followed.

3 minutes ago, r32-25t said:

That’s the only thing you seem to be able to fault with the haltech and yet the best engine management system in the world uses multiple boxes 

Yeah I can't fault them for forgetting tunes. Oh wait yes I can... Multiple times actually ?

Edited by Mick_o
1 minute ago, r32-25t said:

Oh the vcam tune it forgot that turned out to actually be an issue with the vcam itself 

No there was more to it than that. And that was only 1 incident. There were a few attempts to add new firmware patches etc prior. Luckily his coils weren't fried when adding said firmware updates... 

  • Haha 1
6 minutes ago, Mick_o said:

No there was more to it than that. And that was only 1 incident. There were a few attempts to add new firmware patches etc prior. Luckily his coils weren't fried when adding said firmware updates... 

Like how all Ecus should have the coils and injectors disconnected when setting it up?

  • Confused 1
Just now, BakemonoRicer said:

Haltechs aren’t even worthy of being put in Silvia’s honestly. They are the power fcs of today’s ECUs, if you’re a big hitter you obviously run emtron 

If you’re a bigger hitter you run MoTeC 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...