Jump to content
SAU Community

Recommended Posts

I've just spent all weekend trying to get my 02 sensor off with no luck...

I've used the special socket and it's on that tight that it's just stripping back the thread.. Tried WD40 to loosen it and even with a breaker bar and a 22mm socket it still won't budge!

What are my options? :P

  • 3 weeks later...

Replaced my O2 sensor with a nissan universal one from repco, worked ok for 1000km but then started bugging up. Was slightly hesitating at cruising speed then fuel economy went bad and finally engine light came on at cruising speed. My tuner said unplug the sensor and see if the problem is still there, so I did and that fixed it.

So now I'm going to have to replace it again. And this time it's going to be geniuine.

universal = :happy:

'93 HCR32 GTST OZA395-E2 $76.50ish from Bursons trade price, plug fits.

Just confirming for everyone, as this thread lacks R32 info. If a mod could add it to the first post in this thread it would be good.

I just had a look at mine this arvo quickly, been told the front one is playing up, but what did the stock RB26DETT come out with for R33? mine has o2 sensor at the rear with 3 wires, front one has only 2 wires coming from it?

which one has been changed previously? im guessing the one with 3 wires (i.e rear) has been replaced at some stage.

Now if going to buy one, are the front and rear ones the same on R33 gtr? or different part numbers?

on the R33 GTR, your o2 sensors should have 3 wires.

The one with 2 wires has been changed obviously to another type of sensor.

Front and rear are the same but with different connectors thus the different part numbers.

This link should help you : http://wardiz.over-blog.com/article-34295259.html

I just had a look at mine this arvo quickly, been told the front one is playing up, but what did the stock RB26DETT come out with for R33? mine has o2 sensor at the rear with 3 wires, front one has only 2 wires coming from it?

which one has been changed previously? im guessing the one with 3 wires (i.e rear) has been replaced at some stage.

Now if going to buy one, are the front and rear ones the same on R33 gtr? or different part numbers?

  • 3 weeks later...
  • 2 weeks later...
  • 4 weeks later...

I replaced mine recently with a universal one from EL Falcon. Originally tried to solder wires but it's f**king impossible! It comes with a joiner though so i used that instead.

It's working pretty well, fuel economy is better (not sure by how much yet) but yeah see how long it lasts.

PS. Use anti-sieze on all exhaust bolts makes your like much easier getting them off later, thankfully whoever worked on my car did use it and it was piece of cake to get the old one out.

on the R33 GTR, your o2 sensors should have 3 wires.

The one with 2 wires has been changed obviously to another type of sensor.

Front and rear are the same but with different connectors thus the different part numbers.

This link should help you : http://wardiz.over-blog.com/article-34295259.html

This is a good article on changing the O2 sensor on an R33 / R34 GTR. I've added it as a link to my GTaaargh O2 sensor page

If you find any part numbers that fit skylines or other useful links, let me know using the link at the bottom of my web page and I'll update the table. It saves trawling through 19 pages.

James

Here you have it NTK genuine nissan part $77 :)

* Nissan Skyline, R32 GTS-t

* Nissan Skyline, R32 GTS-4

* Nissan Skyline, R33 GTS25-t

http://www.kudosmotorsports.com/catalog/ng...25det-p-42.html

Edited by v8tzr

So the r32 rb20det and rb25det, came with two o2 sensors? one near the dump pipe? and one further down the exhaust, to quote the shop that tuned my car, they think my 02 sensor is lazy, so I suppose it's on the way out.

  • 2 weeks later...

Hey guys,

I have apexi turbo timer with O2 sensor voltage reading feature. How do i know from voltage reading when my sensor are bad?

When i put the ign into ACC (engine isn't started yet), the display reads 0.2 V from O2 sensor. Is it normal? I have 3 inch cat exhaust on my RB20DET, I thought when engine is off, outside air would came inside and make the sensor reads rich near 1 V (a lot of oxygen). Any thoughts?

Thanks

  • 1 month later...

Damn, this is a sticky? Was looking for a replacement O2 sensor for a RB25DE..got to page 12! total confusion.

Guys the O2 sensor only controls EFI in closed loop mode..cruise or light throttle, anything else is determined by your map values and if it's OEM then rich is the key word..to save warranty claims, aftermarket..you need a tune. Sooo your not going to see huge increases in economy, unless you do a lot of highway driving. This means turbo or non-turbo doesn't make a difference as far as the O2 sensor is concerned.

Also like MAP sensors or ECU temp sensors, they are specific to each manufacturers specs, even though they operate in the same range ie. 0-1v NB O2 sensors..0-5v MAP sensors..you need a replacement that duplicates the same specs...

BTW the lower sensor doesn't have anything to do with EFI, it monitors CAT integrity in a narrow band above 1200degF.

Thanks Kudos..going to place an order.

Edited by FTO

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...