Jump to content
SAU Community

Return Flow Intercooler Vs Regular Front Mount Intercooler Question


yoshiii335
 Share

Recommended Posts

Cutting holes is pretty stupid considering it's an instant defect in most states. There are a few ways to get the piping through without hacking holes.

Most of the 33/34 setups I do have return flow coolers, with stock piping in the engine bay. None have been held back much, infact a few have impressed me with their results. If you are trying for dyno queen status it may help a few KW, but otherwise more boost will force more airflow through.

I had similar conversations with the Evo crowd, Plasmaman popped up a few times, but I managed my 300awkw goal on the factory airbox and cooler for a full stealth look, without wasting coin on parts I didn't need. It may make 10 or 20kw more with an expensive cooler kit, but that isn't value for money to me. I guess it depends who you are trying to impress with your mods...

  • Like 2
Link to comment
Share on other sites

Cutting holes is pretty stupid considering it's an instant defect in most states. There are a few ways to get the piping through without hacking holes.

Most of the 33/34 setups I do have return flow coolers, with stock piping in the engine bay. None have been held back much, infact a few have impressed me with their results. If you are trying for dyno queen status it may help a few KW, but otherwise more boost will force more airflow through.

I had similar conversations with the Evo crowd, Plasmaman popped up a few times, but I managed my 300awkw goal on the factory airbox and cooler for a full stealth look, without wasting coin on parts I didn't need. It may make 10 or 20kw more with an expensive cooler kit, but that isn't value for money to me. I guess it depends who you are trying to impress with your mods...

This is why I'm so conflicted, Stao said my struggle to get anymore than 18psi or sustain that (TBH it struggles to even make that) is because of pressure drop in the cooler.... I'm not sure what the actual issue is now. With that being said the tuner said the waste gate actuator isn't very good either. Open to opinion, PM me if you can help/provide insight

Link to comment
Share on other sites

I've seen the turbo make towards 30PSI IIRC but I'm struggling to hold 18PSI, Stao stated that the issue is the intercooler pressure drop but I've got a mate with a 3076 and he is happily running 20PSI on the same cooler. Maybe some characteristic difference being different turbos but I would have thought they should both see the same pressure loss.

Tuner said the actuator is a contributing factor, he struggled to get it to hold 18PSI even using my boost controller.

Link to comment
Share on other sites

This is why I'm so conflicted, Stao said my struggle to get anymore than 18psi or sustain that (TBH it struggles to even make that) is because of pressure drop in the cooler.... I'm not sure what the actual issue is now. With that being said the tuner said the waste gate actuator isn't very good either. Open to opinion, PM me if you can help/provide insight

I'm running a 2013 Hypergear ATR43S22 and a Trust turnflow (vertical flow) intercooler, 275rwkw @ 20psi on PULP controlled by a Blitz D-SBC.

I have about 4mm preload on the actuator arm from memory, set by the master himself (Stao).

Here's a photo of the Trust intercooler, the end tanks are top and bottom as opposed to the sides as in most return flow coolers.

It's still got a sharp 90 degree bend on the top side to clear the chassis rail, may cause some restriction:

13994336254_b0636c4c23.jpg

EDIT: More photos of the installation here: http://www.sau.com.au/forums/topic/348655-r34-gtt-front-mount-intercooler-installation/?p=7265769

Edited by V28VX37
Link to comment
Share on other sites

  • 7 months later...

Looks very similar to my blitz return flow. 
I guess the way the end tank makes the 90 degree bend is different.

Link might not work as it's from my FB but i'll chuck it in just incase.
https://scontent.xx.fbcdn.net/v/t1.0-9/12654460_10153445823391483_8868087888444606538_n.jpg?oh=7abb373099ab59cf6e03d7841d5249cc&oe=585CF425

From what I have heard is people seem to think it's just the core of the blitz that is shit.

I'll know in a few weeks if it's really that bad when mine goes in for a tune.

Link to comment
Share on other sites

2 hours ago, Dose Pipe Sutututu said:

best to run an IAT after the FMIC and see if it's cooling effectively 

Sounds like a pain, at that point on the dyno it will be disappointing if not making neck braking torque etc... i have my FMIC from other skyline that proved easy results so maybe i'll just put that on and make the hole for it, just extra work to rule out shitty intercooler i guess...

Link to comment
Share on other sites

  • 2 years later...
3 hours ago, Girts said:

Is anyone making 300kw and over on the Blitz return flow?

+1 - 320 odd on E85

Been tracking racing my R33 for 7+ years with that set up no problems.

Everyone has an opinion on these coolers but the core is rated up to 500HP by the manufacturer.

E85 really helps keep all temps down... It was easily the best mod I ever did for my RB25

  • Like 1
Link to comment
Share on other sites

+1 - 320 odd on E85
Been tracking racing my R33 for 7+ years with that set up no problems.
Everyone has an opinion on these coolers but the core is rated up to 500HP by the manufacturer.
E85 really helps keep all temps down... It was easily the best mod I ever did for my RB25
Wow not bad at all! Built motor?
Link to comment
Share on other sites

8 hours ago, Girts said:

How many kms do you get to a tank?

It's a track-only car, and not registered. A typical event would be 40 full noise laps of Mallala, plus 8 or so slower outlaps - maybe 120kms total. We would use around 100 - 110 litres of E85, so about 65km to a tank? We didn't build it for economy.

  • Like 1
Link to comment
Share on other sites

My car makes 312rwkw on e85. Track economy is similar to geedog. On the street it does just under 300km for a 65lt tank, non highway driving.

On the weekend i drove 120km + each way to the track, did 25-30 laps of phillip island. Around 420km all up. Used around 145lt of the good stuff.

Link to comment
Share on other sites

On 12/26/2015 at 5:32 PM, V28VX37 said:

I'm running a 2013 Hypergear ATR43S22 and a Trust turnflow (vertical flow) intercooler, 275rwkw @ 20psi on PULP controlled by a Blitz D-SBC.

I have about 4mm preload on the actuator arm from memory, set by the master himself (Stao).

Here's a photo of the Trust intercooler, the end tanks are top and bottom as opposed to the sides as in most return flow coolers.

It's still got a sharp 90 degree bend on the top side to clear the chassis rail, may cause some restriction:

 

13994336254_b0636c4c23.jpg

 

EDIT: More photos of the installation here: http://www.sau.com.au/forums/topic/348655-r34-gtt-front-mount-intercooler-installation/?p=7265769

A quick update for anyone playing at home – this exact setup plus a larger fuel pump made 318rwkw when retuned for E85 in early 2018. So the Trust turnflow definitely goes beyond 300kw.

Dyno sheet: https://www.sau.com.au/forums/topic/55845-rb25-turbo-upgrade-all-dyno-results/?do=findComment&comment=7866850

The car ran smoother on E85 compared to PULP but the fuel uneconomy was atrocious – about 20L/100km on average for the less than 1,000km I drove it for before selling. Still not quite the ~35 l/100km Bill posted above though :) 

Link to comment
Share on other sites

It's not so much the FMIC can go above said power levels, it's more so you need to look at how effective it is at cooling the charged air and how much it can flow. Looking at HP ratings manufacturers randomly put on them is trivial. 

Standard fuels have much less knock resistance than say E85 or PULP w/ water meth. Hence will knock much easier, running E85 your intake air can be close to 100 degrees without you running into any issues where as if you were just on 98RON you'll run into knock, etc. 

 

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Go to SP mufflers and get the muffler of size you want and make a nice mid muffler. It's about that simple! I have 2x 3.5 Magnaflow straight through Mufflers and while it's pretty loud with the Varex open, it's quiet enough with the Varex closed. You can also buy off the shelf Magnaflow straight through mufflers as well. You also have a turbo to quiet the car down too. Don't overthink it. Buy my extra Magnaflow muffler sitting on a shelf doing nothing (buy it new, ignore this part)
    • Centre-offset muffler under the floor, same as stock. Just....3.5". The change from straight pipe there to centre-offset will mean that you need to remake some of the pipe (add a bend or two).
    • Hey guys. So my R34 GTT has a custom 3.5” exhaust (done by previous owner) with a high flowing cat, and then just a Varex cannon muffler on the back. The car does drone alot and is really loud even on highway driving just cruising, as you can imagine due to the Varex muffler basically being a straight through with the valve open. As much as i love a loud RB, it can be a bit much with no other muffling in line and just driving casually. I wanted to lower the volume output on the exhaust a bit, as well as remove the drone (probably a way to do both at once), and was going to do it all myself as I am a fabricator and have done exhaust work in the past, so the fab work isnt my issue, im just not sure on the right product or type of product to use to get the job done, and i doubt an exhaust shop would be wanting to help me as they wont be making any money from helping me, unless they supplied the product? Anyway any help or guidance in best way to approach this would be awesome   Thanks in advance
    • Meh, whilst the Honda is a "really" good car and has potential if you want to drop coin on, it was uninspiring for me to look at, but, it did serve its purpose and is now in the boys hands, his happy, his girl is happy, as she wasn't to keen on the noisy old Patrol, and most importantly, the Minister for War and Finances is extremely happy that her "little baby boy" (6'2 nugget who is currently training to be a copper, which will make 3 coppers in the immediate "circle of trust") has a well sorted reliable car that doesn't guzzle diesel Me, I'm more than happy with the NC MX5 that I replaced it with, it's a fun little car that I like looking at, like driving, and yes..... I do like the fact that the maintenance and modifications that I have done/will do are plentiful and relatively cheap, well........ while staying naturally aspirated slow that is, and that's all I really need for a fun little daily, I can rev the 5hit out of it rowing through the gears and never really break the speed limit  In saying that wicked word, "modifications", I've already ordered something for some noise and an additional "3 ish" horse powers, or whatever it gives, in the form of a header, and, a new set of "cheapo" BC coilovers that are already sitting in the shed waiting to get put in, I had the same BC's in my old NB and found they were fine for the street, hwy, and the occasional track days I did in it, they have 6kg front and 4kg rear springs which is about 10% stiffer than the stock springs which I found worked well for their price  I've also already been in touch with MX5 Mania in Dural, so once the header is on it will get a ECUTek RaceROM tune there (I cannot rev match for 5hit, and I loved the RaceROM rev match and FFS in my old 86 "RIP") In other, maintenance news, I put some new sparkler plugs in it, and have a new set of DBA Street series pads to put in over the next day or so, I'm running the DBA street series in the SS and Honda and really like them, they work great and are not dusty at all I've also booked in a few days leave over this weekend to give me 4 days weekend do some paint correction and give the leather seats some conditioning and interior some Bissell and steam cleaning OCD lovin', the carpet and interior looks clean, but from my experience with the Bissell IRT carpet, and the steam cleaner IRT trim, looks can be deceiving I've also found that finding a detachable hard top is proving problematic, the main reason why I didn't like the NC initially was the power retractable hard top that I seen them with gave the roof line a weird look, the detachable roof though looks good, and is a same shape as a NA/NB hard top, similar, but unfortunately not the same as it has different fixture point on the front, so fitting a easy to get NA/NB detachable hard top is no bueno New Old cars are fun, cleaning, hunting and playing around brings much joy How are your beasties going? Do you still have the Skyline with the LS???, or Barra??? that you were playing with
×
×
  • Create New...