Jump to content
SAU Community

Recommended Posts

Is this build really built for response, 8.5comp and no VCT sounds more like a big boost top end setup??

How would this build compare to a RB3025 neo with VCT and 9.5comp with even 50% E85 mix... surely that would of got big torque low down...

Yes I was trying to get response and from what I had, it is pretty good. It is very linear as it goes from idle to 6500rpm, well that was the highest I could go on the revs before it played up. But when I first came home I did get the chance to give it a launch from 5000rpm and there was a little 4W spin and no lag, so I guess you can say it has pretty good response.

To get near that before I was going from 7500+ rpm and it would still dig in a bit

Have no idea about your comparisons , I am sure there will be some blokes that could answer your question :)

Is this build really built for response, 8.5comp and no VCT sounds more like a big boost top end setup??

How would this build compare to a RB3025 neo with VCT and 9.5comp with even 50% E85 mix... surely that would of got big torque low down...

Has to run on 98 and you have to stop spending somewhere

Everyone would love V-cam....but cant always afford it

Lol, how exactly does VCT help response over dialed static cams when response is all you are after

Yet still yet to see any proof VCT is better then properly dialled cams

The advantage of VCT is that you can dial in your cams for response at as low a revs as possible and then still get a good push further up when your static cams would lag behind. So VCT does not of itself create better response but it enables you to set up for maximum reponse while getting better power further up than if you did not have VCT.

QED

LOL

ROFL

ETC

The advantage of VCT is that you can dial in your cams for response at as low a revs as possible and then still get a good push further up when your static cams would lag behind. So VCT does not of itself create better response but it enables you to set up for maximum reponse while getting better power further up than if you did not have VCT.

QED

LOL

ROFL

ETC

So what your saying is VCT does not help response against cams dialled in for response :thumbsup:

Proven !!, really, where exactly is the proof, i read alot of people saying it's better but still no ACTUAL proof

So what your saying is VCT does not help response against cams dialled in for response :thumbsup:

Proven !!, really, where exactly is the proof, i read alot of people saying it's better but still no ACTUAL proof

Way to be selective in what you read.....

The whole point of VCT is that you can have the (int eh case of a RB25) intake cam set for max twist down low, then have it change over to carry the torque curve further up the rev range....

But Porsche, Ford, Merc, BMW etc etc must all be wrong......

Way to be selective in what you read.....

The whole point of VCT is that you can have the (int eh case of a RB25) intake cam set for max twist down low, then have it change over to carry the torque curve further up the rev range....

But Porsche, Ford, Merc, BMW etc etc must all be wrong......

Lol, kettle black mate

The point started at someone saying built for response but don't have VCT, i posted how does VCT better static cams dialed for response then Kiwi responded basicly confirming what is said

At no point did any one mention response AND topend :/

As the guys mentioned, i have posted my graph of my stock factory RB26 more then once for people to beat for both bottom end as well as top

And i'm still waiting

We are also only talking RB25 VCT V RB26, or any other cam timing setup that only changes the inlet cam timing from one maximum to the other, though would love to see how a RB with the VE cam setup would go

.....

As the guys mentioned, i have posted my graph of my stock factory RB26 more then once for people to beat for both bottom end as well as top

And i'm still waiting

....

ooooo.....where?

Xkalaba, don't take it as a personal attack you have to defend!

I don't like your chances of getting a guy with stock turbos chucking vct on, so I don't think you will ever get the direct comparison you are after.

What's your idle like with the dialed cams?

Xkalaba, don't take it as a personal attack you have to defend!

I don't like your chances of getting a guy with stock turbos chucking vct on, so I don't think you will ever get the direct comparison you are after.

What's your idle like with the dialed cams?

Spends 8k+ on VCT kit but keeps stock turbos :rolleyes:

Idles like a babies bottom, smooooth as

Not like the 34, lol

Like i said, i'm happy to see a NEO with any turbo you like, so given the NEO has a "better designed combustion chamber" and NEO and the latest tech single turbo you can get it should easy walk over my 80s tech bush bearing factory twins on a static cam setup

I want to see same boost (19psi) run 290+rwkw and beat my 26 for response then prove it on the drag strip cause we all know dynos can be made to lie

I'm starting get personal about it cause every time i come on a performace thread someone throws up should have gone NEO or VCT and saying it with no proof is misinformation

ooooo.....where?

Fark it, cause one more time won't and you asked so nicely :P

post-36620-0-27148400-1429787456_thumb.jpg

This graph was done at a SAU dyno day back in 2007 4 days after the full wieght plus stereo R32 GTR ran back to back 11.3@125mph with a stock motor, the stock turbo world record in the link in my sig

  • Like 1

Fark it, cause one more time won't and you asked so nicely :P

attachicon.gifimage.jpg

This graph was done at a SAU dyno day back in 2007 4 days after the full wieght plus stereo R32 GTR ran back to back 11.3@125mph with a stock motor, the stock turbo world record in the link in my sig

I should have bought your car from the get go, would have saved me a shit load of money and hassle , haha

  • Like 1

I need to learn more, but arnt the RB26 and the neo25 pretty similar heads ( apart from VCT) , if they arnt that much different then the VCT would of been good, in comparing response im thinking about how 34GeeTee's 2.5L graph with the HTA3076 has 280kw's at 4000rpm and that doesn't even have a stroker kit...

Edited by AngryRB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...