Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...
  • 2 weeks later...

Sold out of CPH today, they got bought some Canadian medicinal marijuana company...

So if 20% of my holdings are over 12 months old... does that mean I only pay tax on 80% of the profit, since those shares I've owned for less than 12 months?

So if my first buy is at a loss... I pay no tax?
Then second buy is all the profit and all the tax.


Yes. Or the first buy losses offsets the second buys taxes.

That's the way the accountant told me to do it, treat all buys as individual transactions (as they are) and sales take shares out of the earliest transaction until it's done then move on to the next oldest. If you do it that way the tax office has nothing to argue about you doing anything dodgy.

The CGT reduction is 50%, so you only pay half the tax on profits from any capital holdings over 12 months old. If that's 20% of your shares, then you can nominate ANY 20% of your shares in the company to apply the reduction.

As you haven't sold any of the shares you have realised a loss yet, so even if those older shares were sold at a loss, it's irrelevant. What matters here is your average purchase price and your average sell price - what is left over is your profit. 20% of that profit you could argue should only be taxed at half the rate, whilst the remaining 80% will be taxed at the full capital gains tax rate.

  • 2 weeks later...

Litecoin surging... At break even point. Will probably pull out soon and re-enter later once it dips (and it will).
Got to try and remember how to use my ledgerwallet now... lol

Speaking of pulling out... What's a realistic budget for a wedding? Not looking at receptions at this point... So just venue, snacks/catering/seating, photos, flowers, celebrant etc.
Asking for a friend who is budgeting for the future.

Ignoring reception I would think it would cost circa:

 

pre marriage course 240
Veil 260
Dress 3610
Photographer 3600
wedding cars 1660
Church 800
invitations & stationary 1419.49
Florist 500
Her wedding band 2300
His wedding band 735

Get married at the registry - in and out in 20 minutes. Genuinely one of the better weddings I've been to. Your guests will love you for not making them stand/sit still for a couple hours and the bride has no excuse to be late.

Spend the rest of the money you saved on a reception at with a 9 course meal at Sake down the road in their private/basement function room/bar; walking distance so no transport required. Guests will also love you for this.

  • Like 1

a custom designed titanium with a gold inlay....

and to be married in a church you need to do a pre-wedding course, which I thought was a load of bollocks till I did it and had some good stuff. 

Oh and lots of religious stuff.

My sister is doing the registry thing later this year and a big reception. I for one, do appreciate it not sucking up an entire weekend.

Personally, itd be nice to get it all over and done with in one afternoon. Engagement party to merge and meet families etc, that's about it. I know friends want to be involved but isn't it just easier to include a small handful and keep it low key?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...