Jump to content
SAU Community

Air-conditioning Drain Pipe

kingtube69

By kingtube69,
in General Maintenance

 Share

Recommended Posts

kingtube69 Experienced

kingtube69

Posted
Posted

Hi All,

My AC drain pipe was sitting against the dump pipe on my R33 after I put in a Hypergear turbo (ATR45SAT). I had it taken to JEM to get tuned but on the way home it started smoking so I bit the bullet and cut the drain pipe so I could get home without it smoking up and catching fire.

I'm not sure what to do now because if I use the aircon its going to drain onto the dump pipe and steam, rust and more than likely crack.

Has anyone come across this before? If so what did you do to fix it or get around it?

Pictures below

AD709293-2F53-459D-B56A-A6FADF6617BD_zps

E28070AD-2D5F-4D05-B6F9-8CAFD865F3C4_zps

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/461606-air-conditioning-drain-pipe/
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
Posted

Thanks to the thick adapter Tao welds on it pushes the dump back too far which melts the drain. If it gets bad enough it will flood inside the car. The dump will be fine as long as it isn't wrapped.

kingtube69 Experienced

kingtube69

Posted
  • Author
Posted (edited)

Thanks to the thick adapter Tao welds on it pushes the dump back too far which melts the drain. If it gets bad enough it will flood inside the car. The dump will be fine as long as it isn't wrapped.

Yep I'm not sure why it's so thick, I was worried that the dump would actually fit when I was looking at it.

So you think its OK for the drain to drip onto it? Not wrapped dump anyway :)

Fark, is that what the burning smell was when I went single. Just checked and mine is burnt down. So does it need to be rectified or is it OK to leave?

Glad to know I'm not the only one - Waiting for responses but someone on SAU FB page said just get a heat sleeve and get that onto it which I'll probably do if Scotty says that letting it drip on there isn't OK

Edited by kingtube69
89CAL Grand Master

89CAL

Posted
Posted

Get a steel pipe that will fit neatly inside the hose and clamp it on. Get a p-clamp that fits around the pipe then and bolt it somewhere that will bring it out of the way

Thats a basic idea but you can bend the pipe etc to make it fit properly

kingtube69 Experienced

kingtube69

Posted
  • Author
Posted

Not only will you find disgusting water splashing in the passenger footwell, you'll find your car filled with mosquitoes!

It doesn't leak into the cabin, its cut on the engine side and can still drain out its just that I dont want it running onto the dump pipe

Get a steel pipe that will fit neatly inside the hose and clamp it on. Get a p-clamp that fits around the pipe then and bolt it somewhere that will bring it out of the way

Thats a basic idea but you can bend the pipe etc to make it fit properly

The issue is that the bend in the rubber hose actually sits on the dump if its in place :(

zebra Grand Master

zebra

Posted
Posted

Yet... Let it melt back a bit more.

Poorly designed 'drop in' turbo considering most of you are running the exact same JJ dump.

Those hypergears must sit so far back....ive got like 4" clearance with my bolt on td06

hypergear Grand Master

hypergear

Posted
Posted

Its got plenty of clearance using a OEM dump pipe. Or should JJR be making dump pipes following OEM dump pipe angle? But Having said that not all jjr dump pipes touches either.

That Xforce dump in my R33 years back was trouble free, and so is Tomei.

I will seek alternatives ways to get the IWG assembly shorter.

kingtube69 Experienced

kingtube69

Posted
  • Author
Posted

Hmm, it's not that the lower part of the pipe sits against it so it would be hard to tie it off to the side. It's that the bend off the pipe sits against the bend of the dump pipe. Bit of a pain in the ass but I'll work something out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...