Jump to content
SAU Community

Recommended Posts

Short story:

How Do Vented Gas Caps Work?
By Steve Smith
eHow Contributor
Save
6 Shares & Saves
Vented Gas Cap Function
  • The vented gas cap is designed to vent small amounts of air into the car gas tank line. The vented gas cap has a one-way release valve that is pressure-activated. When the pressure reaches a certain point (defined by so many pounds per square inch) the valve opens by a very small amount, relieving some of the pressure. In this case, the pressure is formed on the outside of the tank, due to the vacuum formed from the displacement of fuel on the inside. After the pressure inside the line equalizes, the pressure valve closes. The valve is set to balance the pressure with the surrounding atmosphere. Air is allowed in, but no fumes are allowed out of the gas cap, because of environmental concerns.

Inner Parts
  • The vented gas cap has a chamber under the plastic cap handle that inserts into the fuel fill line. The cap screws shut, and this chamber fits relatively close inside the intake tube of the fuel line running to the tank. On each side of the chamber are small openings where air is able to enter. These chambers lead to the pressure valve, which, as the level in the tank decreases, allows air inside to remove any possibility of a vacuum forming.

How it All Works
  • Because the fuel tank is pressure-driven from a fuel pump and gas naturally expands and evaporates, a large amount of pressure can build up inside the fuel system over time. This second kind of pressure is taken care of through the operation of the fuel pump mechanism, as the vented gas cap needs to be the one-way flap to keep evaporated gas fumes in.

All that I know from personal experience is that they are only supposed to vent one way and that it is important that they vent correctly.

  • I had one in a Subaru stop venting and the steel fuel tank started to collapse because of the level of vacuum being created.
  • In our R33 track car the cap started venting both ways which resulted in fuel covering the rear of the car - not a great look when you have the usual flames from the exhaust

thanks gents that is exactly the part I was trying to get to. funnily enough it struck me that the workshop manual might have some information, and voila!

fuel-cap.jpg

so yes, the GTR cap has a one way pressure sensitive valve that allows air in to replace the used fuel (but not out, of course)

the other half of the breathing is the "fuel overflow prevention system with check valve" which breathes excess pressure into the charcoal canister when the engine runs.

the motorsport question of course is what is needed to safely vent the tank, I don't want to sit on a fuel bomb. Pretty much every aftermarket vent is an anti roll over valve which is open at all other times, ie it allows air/fuel vapour in or out unless the car is exactly upside down.

ideally I would keep the stock cap and have a 1 way valve to allow fuel vapour to vent to atmo (via a small filter) but I am having trouble finding something good. most setups are small valves near the top of the tank that are almost guaranteed to leak fuel from a full tank in high G corners. In fact the most common valve mounts on top of the tank and doesnt allow for any venting hose at all

Some people combat that by having looped breather hose but as soon as you get liquid fuel into that hose it can no longer work as a vent which defeats the whole purpose. kind of like a S bend with the same result that gas cannot pass.

happy to hear any suggestions about a good way to deal with the venting

We had a failed breather on our EVO at the Winton 300. Caused the fuel bladder to expand, pushed the carbon bucket down onto the drive shaft - and wore a hole through the middle of it.

Thankfully we didn't a) blow up (it's right next to the exhaust) or even b) run out of fuel at the end.

I'm still not 100% sure how either of those didn't happen however.

So with the new fuel bladder we now have 4 breathers rather than 1.

post-5136-0-68034800-1455765554_thumb.jpg

lucky outcome really....

I was not happy with the design of some of those breathers they are very basic. Have you got a pic of how the 4 breathers are mounted and vented? Are you using a 90L FIA with siamese fittings?

I actually haven't seen it and it was fitted before I got the chance sorry..

It was your new mate Dylan Thomas who did the 4 vent design. He had previously suffered the same thing we had with the base Ralliart design so they did a 4 breather design. I actually just purchased Dylan's old tank as they were going from the saddle design to a boot mounted flat design as he was being team serious and wanting to extract every last litre out of his tank for 6hr .

I personally am not a fan of the safety aspects of a boot mounted tank though but that's a different topic to this one.

But Dylan would be a good bloke to chat to about fuel tank breathers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...