Jump to content
SAU Community

Recommended Posts

Same here, Supercharge but Gold series across all our cars for availability, warranty, cost, configuration variations and performance life. If I can't get these then only Century.

Would love to run the Supercharge AGMs in the Nissans but they don't have the pencil posts and varied post positions available like the Gold series.

  • Like 1
2 hours ago, Dose Pipe Sutututu said:

Looking real nice!

I've moved away from Optima, they aren't of the same quality as they used to be!

I now run a SuperCharge battery (made for Stop/start applications and is an AGM battery - similar to an Optima), not to mention it's an Aussie brand with 3 year warranty.

https://www.supercharge.com.au/car-battery/supercharge-start-stop-car/?post_type=battery_type&p=173

All the in-laws' cars run their SuperCharge Gold range batteries, cheap and phenomenal warranty.

Cheers Johnny, shall look into it...

39 minutes ago, BK said:

Same here, Supercharge but Gold series across all our cars for availability, warranty, cost, configuration variations and performance life. If I can't get these then only Century.

Would love to run the Supercharge AGMs in the Nissans but they don't have the pencil posts and varied post positions available like the Gold series.

Cheers Benny

1 hour ago, Dose Pipe Sutututu said:

I bet you're excited!

Also I would recommend using some form of heat shielding OR wrap your dump/downpipe to prevent your O2 harness melting at the track.

when u say o2 are you referring to the wideband? same same...?!?

as that's just cable tied in that position now til we workout where it will enter the car...

excuse my dumbness, these are the sides of cars that I fail at...

Edited by mr_rbman

For the Wideband O2 sensor I just go through the existing egt floor bung and a Haltech O2 sensor wiring extension harness. Don't want to drill more holes in car than necessary.

  • Like 1
Just now, BK said:

For the Wideband O2 sensor I just go through the existing egt floor bung and a Haltech O2 sensor wiring extension harness. Don't want to drill more holes in car than necessary.

ye that was my initial thinking...

just so I wrap my head around this, both a narrow band and wide band sensor are essentially both just o2 sensors correct!?!

 

1 minute ago, mr_rbman said:

ye that was my initial thinking...

just so I wrap my head around this, both a narrow band and wide band sensor are essentially both just o2 sensors correct!?!

 

Yes

  • Thanks 1
33 minutes ago, BK said:

Wideband gives you an actual afr / lambda ratio, narrowband just signals whether it's richer or leaner than Lambda 1 / AFR 14.7:1.

Clear as now, cheers Ben

54 minutes ago, Dose Pipe Sutututu said:

Just delete the OEM narrowband junk, since you now have a modern ECU.

 

tis already gone, just the one wideband roughly 1000mm from turbo..

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...