Jump to content
SAU Community

Recommended Posts

8 hours ago, usmair said:

Can only work with what we've got.......

Umair , it was great to get your info, what I meant , if it had been the 6266 it would have made the 8374 low end response look even better , but I think the top end would be pretty close with both turbos

Umair,

I took the liberty of converting your results to excel and graphing them vs my pumpgas results (including corresponding boost curves). Looks like my combo of stock-bore 79mm stroker (2.75L) and/or the .92 IWG housing turbo is making a bit more bottom end than yours (below 4500 rpms), but obviously with higher boost and E85 you're crushing me anywhere over that. The boost is x10 for scaling purposes (ie 100 = 10 psi, 200 = 20 psi, etc). I'm willing to bet when converted to E85 and when I start pouring on the boost that I will make more power lower in the rpms, but not significantly so (maybe 250-300 rpms sooner), and with the increased backpressure of the .92 housing I'd bet I'll start dropping sooner as well.

Good looking dyno! :1311_thumbsup_tone2:

 

Dyno comparison to Umair.JPG

  • Like 2
Not really surprised there though. Bigger engine making more grunt down low.

How long till you put it on E85, Harris? 

Station is targeting completion in november. I'm hoping to have fuel pumps, 3.5" exhaust, and mega huge injectors done by then. I'm still on stock fmic so we will see what it can flow!

will need 100m cooler. the stockies have been known to hold power back over 400kw.

3.5" will do the job. Mine is 3.5". 4" only if you know you are going to aim for even bigger power in the future.

My injectors are 2000cc. I was told that even 1600cc on e85 wont cut the mustard for 500kw. Makes it a little harder to fine tune but its not noticeable in day to day drive.

thanks for mapping the dynos. interesting stuff!

  • Like 1

If anyone is interested, I'm maybe going to the SAU cruise to the Gosford car museum on Sunday.

Happy to take anyone for a spin so they can feel the setup for themselves.

Edited by usmair
if you need pricing on Plazmaman coolers @usmair give me a holla [emoji4]


What about me? Sounds like he's got a cooler.

I'm almost tapped on money these days (oilfield sucks here lately). I need a sponsor!
43 minutes ago, HarrisRacing said:


What about me? Sounds like he's got a cooler.

I'm almost tapped on money these days (oilfield sucks here lately). I need a sponsor!

haha but you're in the US.. shipping won't be cheap.. however happy to help out - flick me a PM on which size cooler your after, and if polished/black/raw etc..

What range of mph would you expect to get from 500kw 

 

138-140mph??

I would hope! Thats a ton of power. I ran 120 mph on 464 whp and you've got way more midrange.

On 9/3/2016 at 11:53 PM, Piggaz said:

Borg Warner EFR Series Turbo's V 2.0

 

Link to the first attempt. A wealth of knowledge in it. 

annnnd go!

We gonna be factual on this or its gonna b like the last one >_<

What wasn't factual in there? 

You must have some EFR experience to share with us if you know there was nothing factual in there? 

 

 

Edited by Mick_o
  • Like 2
On 9/10/2016 at 10:00 PM, Mick_o said:

What wasn't factual in there? 

You must have some EFR experience to share with us if you know there was nothing factual in there? 

 

 

at the end of the thread which got it locked . 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Resizing injectors in Nistune can be done a couple of ways, and there are a couple of ways that you can make a mess of it. The tuner needs to be really aware of the effects of whichever approach he uses (either K, or TIM). They are both easy enough to "get the injector size right" to run the engine. But little details like old start enrichment and hot start are affected differently, depending on which boxes you check.
    • Pretty safe to say almost everyone that has tuned their own car has experienced this issue. The difference being that we have our laptop in the car and when it happens, it's literally 10 seconds of tuning to sort it.  Would you be happy to plug in your laptop and sort this yourself? It is a very simple process and there is no risk of harming your engine (if you are worried about that). 
    • Yeah thats the next step now, either they wil or i will take out for a drive to work and go straight their after work and see is we get the same issues 🤞  thought i try my luck here too, never know someone else might have had the same issue but thanks for the reply 
    • Basically your tuner needs to drive it for the 30 min (or whatever) to create the same conditions then check the ECU settings and sensors at that time. They may not be excited to because that takes them 30 min rather than just opening the bonnet and seeing the problem straight away.... Hot start is generally not as tricky as cold start, but there would be a table for fuel enrichment vs coolant temp as a starting point
    • Yeah, they all cant say anything for sure as everything is working fine . Said unable to find an issue untill it stops again. Could mist likely be CAS wiring or IAS valve issue but again not 100%
×
×
  • Create New...