Jump to content
SAU Community

Recommended Posts

Only a few small updates, needed to block off the internal wastegate flap, managed to get this Cobb Racing part that looks pretty good! 

 

Having troubles getting the exhaust manifold back on. Both the original and my new one won't fit. I'm thinking the manifold studs may be warped, so have ordered some new ones and hopefully that fixes it!! It fits on the ends but not the centre studs for some reason.

20210116_201652.jpg

20210116_150925.jpg

Edited by Tobz

Was the original manifold tight to get off? You'll probably find your manifolds are warped slightly. I had 4 manis in my spare parts pile. 2 of them wouldn't fit when i tried them. 

If replacing the studs doesn't fix the problem, you could try enlarging the bolt holes that require it as a quick fix and hope it bolts down good and doesn't leak.

When i had asked an engineer at work about machining the face of the mani, he didn't recommend it and suggested heating it up and straightening it was the best solution, obviously requires special equipment. I ended up just binning it and using a good spare.

Another thing you can try is removing the studs that are fouling, put the mani on and see if you can thread the studs in from the outside. If that doesn't work, at least you'll see how far out the holes are and how much to relieve.

  • Like 1

Yer manifold was impossible to remove, used many breaker bars, however I have a replacement manifold from hypergear to go on. The new manifold may also be warped though as it's a stock manifold with an external gate welded on. I'll change the studs and see where that leaves me and then contact hypergear if there is an issue

New studs arrived and now the manifold fits perfect. Looks like the studs warped pretty badly, but the manifold didn't... Which works for me!

Just need my new turbo studs and a silicone joiner to arrive and then it should be all back together. 

Also does anyone know what the effect of swapping to a proper cooler from a return flow, and going from an iwg to ewg would have on the tune? I'm getting the car retuned either way, but just interested to know if I can take it for a bit of drive to test everything is bolted up right (and get it on boost to see if all the couplers and such are all holding fine).

20210124_195309.jpg

Edited by Tobz

Cooler? Nothing - Unless your IAT actually changes as a result of it. I've seen people spend big on an intercooler for an 0kw difference.

IWG to EWG will make a considerable difference as this actually changes boost. Presumably though if you're already MAP based going from say 16PSI IWG to 16 PSI EWG won't change much, you're more likely to notice that your 16PSI is actually holding rock solid to 7500RPM whereas it may not if 16PSI was your target on an IWG (i.e as hard as you could max it out).

You may notice something by holding boost better. Most people go EWG when they cant hit their desired target with IWG.

  • Like 1

Yeh just keep an eye on your boost levels, both mods have the potential to change how much boost and when it comes on, which can mean you run lean in certain areas of the map.

Intercooler doesn't necessarily have to change your IAT, a return flow is always going to be a fairly large restriction to flow. If you then change that and make it flow a lot better, you lower the potential for boost drop, and more importantly you allow the boost to come on earlier. Depending on how your car was tuned, that could be an issue if you have moved the boost graph to the left. If you have a good boost controller you should still have the peak boost level under control, but where it occurs on the map is potentially different. Couple that with the effects of changing to a EWG as well, which Kinkstaah nailed, and you have potentially given yourself quite a bit of extra range in the map where you are at peak boost. 

 

So just be aware. It's definitely one where you want to get your tune checked, because who wants to lunch a motor (especially in this day and age!) because their mods worked. I wouldn't be too scared to take it for a test drive and at least get it ramping up to full boost in 2nd gear, but I wouldn't be holding it on peak boost just for the sake of seeing if your couplers are holding. 

  • Like 1
  • 2 weeks later...

Finally got the car back together and took itmfor a drive. 

Changes to the intercooler and external wastegate have changed everything.

Before I was told the turbo was being restricted either by the intercooler or exhaust.

Having swapped out the return flow and also going to an external gate has released the restriction

It needs to be retuned as the power is defo coming on early, but also the ebc cannot control boost. Did a slow pull in second and the boost crept past 20psi which should be the limit.  It's a Mac valve and a 14psi spring on the gate. Looks like it may need some setup done on it

AFRs all looked good.

Trying to organise a time to get retuned now. But overall so far I'm very happy

Also added a 5inch body venom cat, installed some Sparco r100 seats and got the harness installed! 

 

20210207_135939.jpg

20210130_200545.jpg

20210207_140042.jpg

20210207_140109.jpg

Edited by Tobz

Thank you for posting a pic of Sparco R100's - I was thinking of putting those in.


What rails did you use? There's an ebay mob selling a kit, but I never got that far. I wanted the black leather ones 😛

How do they work/fit/comfort wise? Looks like enough clearance.

12 hours ago, Kinkstaah said:

What rails did you use?

I used the crank motorsport seat subframes and just universal rails :)

 

clearance was more than fine. Seats are a little hard but more than fine, nice bolstering. Overall I really like them

Edited by Tobz
  • Like 1
  • 3 weeks later...
1 hour ago, Manuel Kasko said:

Oh man what a journey! I just read from start to finish and I'm stoked with what you've done with the car since I sold it. 

Keep the updates coming Tobz! 

It was a super solid base to work from! Love the little beast!

  • 3 weeks later...
5 hours ago, JarrettL said:

How does the X-Trail pedal fit up compared to the 350Z? I've read that the Z just bolts right up, but the pad position falls slightly too close to the brake pedal unless modified.

 

Can confirm on the 350Z pedal. It's super easy though, just throw it in the vice and bend it a little bit. Its a steel arm, so not going to break and you can manipulate it around to your liking. It only needs to move like an inch to the right, and fitment otherwise is perfect.

  • 2 months later...

Went to the dyno day today. Can now compare all dyno runs I know of.

First is from the previous owner when it was first tuned in Feb 2017 from DVS (287kw)

Second is from August 2019 (271kw) when I did a dyno day in Canberra at Autotech Services

Final one is from the SAU dyno day today (305kw) at JEM

I don't believe there was any changes to car between 2017 to 2019 other than an owner change :)

Changes from 2019 to now are basically Haltech, external gate and a proper intercooler. It is also now running a bit richer now (afr went from! low to mid 12's from 2019 to low to mid 11's now). This is due to the car doing a lot of track work now.

It isn't making as much power as I wanted, but I actually think this is fine, it comes on hard but stays super flat to redline. Very happy

 

 

 

16194869_10154375981131483_3091880825224997122_n.jpg.4189582d5c262027d0104079a280f6dd.jpg

Scan22052021170425_001.jpg

Scan22052021170546_001.jpg

Edited by Tobz
  • Like 5
  • 3 months later...

So car was running fine and then I went on a holiday before all of Australia locked down. The car sat all alone doing nothing for about 2 months.

Got home and took it for a spin and it started leaning out. Looks like the injectors may have clogged up while it was sitting as it was still on E85 and didn't have any fuel stabiliser in it before I went away. I assume this is a thing?

Anyway got the injectors out today and will be sending them to get cleaned and flow tested.

Not sure why but have also decided to swap to a Plazmaman front facing plenum. I know it doesn't really do anything, but I wanted to clean up the engine bay. Also the way my car was converted to DBW it meant I couldn't run a strut brace anymore, and I know it doesn't do a lot but I do miss it.

Put the order in today and looks like it's a 7 week wait! But I think it will clean up a lot and just make it easier if I need to do any troubleshooting trackside.

Super annoying that there was an issue with the car, but at least it happened when I can't use the car anyway!

It shouldn't really happen, we've got a couple of track cars on E85 that don't get used much and often don't get started for 18 months - 2 years, but they always start up and run ok. You obviously wouldn't do any full load stuff, the fuel won't be any good anymore, but that's more about its ability to prevent detonation than it is about clogging anything. 

 

That said, it's possible, and always worth doing a full check of the fuel system as you're doing.

  • Like 1

Consider your fuel filter. I had considerable issues with the R34 Ryco style fuel filter if I changed fuels, or let E85 sit around. It would clog to the point where making 300+kw would start to run lean.

Something to check if your injectors come back OK. Well worth checking the injectors first though/as well, as you don't want to be running rich on 4 cylinders, and lean on 2 etc!

  • Like 1

I pulled the filter and it seemed pretty clean, I'm going to give it a good clean later on (have an inline micron filter with the stainless steel mesh).

However I don't believe it is the filter as my FPR is on the return line and I get my fuel pressure from that and it didn't drop pressure... Was holding pressure really well.... So I'm hoping it's the injectors, as that's a super simple fix. They are currently off being cleaned and flow tested

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...