Jump to content
SAU Community

Recommended Posts

15 hours ago, GTofuS-T said:

You could also replace/upgrade the return springs to give it a tighter feel

There are 3 options hard, medium, soft, which one to choose without trying them all out ?

Anyone have opinions on the return spring, also brass or nylon bushing.

Thanks

No way will you tell the difference between a brass or nylon bushing.

 

The springs are cheap as. Just buy them all and find what you like.. Or do you prefer some random guy to tell you their prefefence?

Buy a new cup, wave washer and shifter bush from Taarks or Kudos. Get shifter springs from gktech. Do fresh gearbox oil with a tube of nulon smooth shift. That's about the best you can do. Stay away from the ebay offerings. 

  • 6 months later...

Don't mean to bring this thread back from the dead but I have also been thinking of a new shorter throw shifter for the GTR.  I know there's pros and cons I've read on here about this, but seems like the Nismo 25% one is good and about $300 (USD) here in Japan but the Cube speed ones look nice too and are less expensive.  People really prefer OEM over one of these models? 

Example of the Nismo 25% reduced shifter: https://page.auctions.yahoo.co.jp/jp/auction/g424885412

I have a hardly used Nismo 25% quick shifter here that I was running on the 32R with an OS giken 5 speed. It was awesome - the tightness changed and is very very short shifts, but very positive. I rate them.

I've since changed to a dog box but have the stock shifter with that box now, as the stock shifter is a bit quicker to remove. I should try the quick shifter with the dog box, but I have heard of it not being good with it. I might stick it in the 33.

1 hour ago, WR33KD said:

The cube speed shifter comes with everything you need to swap it. Far far better than the nismo shifter. I have had a chiza, nismo and now a cube and the cube wins hands down

Do you have the standard or the "premium" cube shifter?

  • 1 year later...
On 01/02/2020 at 2:43 PM, Rios said:

So you think I should just get a new bushing brass or plastic ?

Check out this guru - good ol' Americans make me laugh 🤣

I knew there was a reason I was so sceptical about ever using a brass shifter bush....

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...