Jump to content
SAU Community

Recommended Posts

When people say the Michelin Pilots are great or bad, are they talking about the Michelin Pilots Sports, or Michelin Pilot Preceda?

And has anyone has experience with the Avon brand of tyres? I see on www.tirerack.com that the Avon Tech M550 A/S "beat" every other brand of tire (ultra performance, all seasons category).

I have Ziex 326 and wanna upgrade to much better ($300-450/corner) tyres, as I'm sick of spinning the wheels in 1st, then 2nd and even third from the lights without even trying! Not even modified either, just exhaust :) Wear isn't so much an issue as I only do about 15K kms a year and it's mostly city driving with the ocassional coast trip (which is all highway anyway, no off road).

haha anything will be better than 326s!

I back falken fk451 or dunlop sp9000, they are both excellent road tyres, but depending on size they are up to 500 per corner.

OK. but didn't really answer the question...

Michelin Preceda or Toyo T1-R will cost me a bit over 400 a corner and lots of ppl have been talking about them so immediately they are ahead compared to any $500 tyre. 1600 i can *kinda* justify, but definitely not 2 grand.

Then again, this site with the Wheels test: http://www.aussiefrogs.com/forum/printthread.php?t=23777

says there is less than 5% difference between all the tyres in the test (5% in what I wonder.. too vague). Anyway, I have just seen the Maxxis Victra MA-V1 in 235/45 R18 for only 209 each @ Bob Janes.. so the Maxxis Victra MA-Z1 couldn't be a whole lot more (even if it was 100 more, that's still only 300 a corner). I would expect about 250-260 each.

Has anyone had experience with these tyres that are supposed to provide comparable performance to several 350-400 buck tyres? Apparently my Falken 326's cost about 200 each.. I find it kinda hard to believe the Maxxis could do so well for so cheap, so I really wanna hear from anyone who has them (and has owned enough tyres to compare fairly).

what size rims rice, the new fedrels are not to bad i have some on the rear, and after the first few weeks they have settled in very well, little spin in first then nothing but hook up in second.

r33 gtst 216rwkw 18 /265/35 the new ones have a lot more silica in them, so before ppl go baggin them there different now

!!! RICE?! ri*N*cewind :P man.. hope most ppl aren't reading it that way lol uh nevermind :) Those who know, know.

Rim size is 235/45 R18. I dunno about the width.. how can u tell by looking? I didn't put them on myself so I dunno.

Quickfit just 5hat on Maxxis from a fair height.. saying they are a long wearing budget tyre (about 40k's instead of 25-30k), that they sacrifice on grip, and that Wheels is a biased magazine and the next magazine on the rack will push some other tyre make/model. He also said that they don't have much experience with them though.

Grr

had falken 326's on the rear... and they were ok in the dry and just death in the wet.. anyways after spinning out just the other day.. i put my foot down and decided to ditch the falkens as they were ABSOLUTE rubbish

replaced them with the same size (245/40/R18) as before but toyo TPG's

paid $540 fitted for the two

and they have worked out allright.. i wouldnt say they are fantastic... but as an upgrade on the falkens they are damn good.. i wanted t1-r's... but found out how expensive they were

i give the toyo tpg's a wet: 6.5/10 and dry 8/10

value for money would get a 8/10

I just got quoted 250 a corner for Maxxis MA-Z1. I can't go past that, seeing how well they did in the magazine road tests (I heard Motor gave them a good review too), for 1K as opposed to 1600, the decision is now all but made!

The fitter said the reason they are so cheap in Australia is cos they've only been in the car tyre market here for about 2.5 years. My mechanic also says they're great, so I'll give em a go.

I just got (after recommendations in this thread) Hankook K104s... unreal tyres, I got:

-255 * 40 * 17 (rears, 9 inch rims)

-235 * 45 * 17 (fronts, 8 inch rims)

Very sticky at the moment... I have a stockish R33 GTS-T, and full throttle out of most corners I have problems spinning them at all, lol, and the rear end is very very stable. Wet weather driving is great too. But coming from Falken Ziex 326s, anything is a huge step up.

Will report back in ~10,000kms anyway.

since they wieght of all skylines are in the 1300 - 1600kg range I reckon the recommendations are pretty relevant. Suspension mods make much more difference to tyre performance that power.

Unless you mean rear traction problems out of big power cars?

Either way, if you buy a sports car, modified or not, buy the best tyres you can afford for it, they make more difference to performance than any other mod.

I had the Toyo T1R for almost 2 weeks which I put them in the front (235/40/18) and in the wet holding is pretty good plus confirdent. Dry is excellent. I am waiting for my rear sets next week (265/35/18). I was told it's better than Yokohama AD07 in the long term usage. You guys reckon it's true?

haha yeah Snowman knows the deal, not that it matters now :P

rincewind was better! LOL

I actually tried to get the personal plates BINKY in Vic but they were taken already.

Anyways.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...