Jump to content
SAU Community

Recommended Posts

My engine head gasket went last night on the dyno due to a bad wiring in the fuel pump lol. I was about to test it out. So hopefully in about a weekish.

The new pump requires an additional earth. By the way it is a walbro F9000262 400L/Min pump. It works once plugged into the stock loom but doesn't create much pressure. Once additional earth is connected it worked fine. How ever didn't help the head gasket.

Don't know why people use anything but the good old 040. Never heard someone complain about one!

Cant forget the Nismo pump, it plugs right in, is good quality and pumps and decent amount of fuel :yes:

Having used three of them in the last week I have nothing bad to say about them other than that they are driving me mad by failing right out of the box due to clogging!

(I realise this is not a pump issue :P)

Birds, even the 040 needs a good power supply, in fact I would be upgrading the power for any aftermarket pump as they require up to 4 times more current. Stao found out the hard way that the stock wiring can't supply 17 amps. Sorry to hear mate.

Don't know why people use anything but the good old 040. Never heard someone complain about one!

Because we are cheap bastards Birds ;) Do wish I had gone with the 044 back when I did my fuel pump, didn't think it would be necessary at the time though. Nor did I realize how good a noisy fuel pump sounds!? :P

Interesting that it failed on the dyno though, was the fuel pressure not being monitored or is it just one of those things?? Makes me want to check my fuel pump, though I have rewired mine and has been sweet so far.

I had 040 in my Sil180, when the metal filter blocks it makes a loud whining noise. I had to pull it out and clean it once every couple of weeks, on the end I teared the mash filter out of the bottom and that worked fine and stopped the whine. lol

The walbro more or less bolton to stock bracket, and it had an walbro in there for 4 years without much issues.

Because we are cheap bastards Birds ;) Do wish I had gone with the 044 back when I did my fuel pump, didn't think it would be necessary at the time though. Nor did I realize how good a noisy fuel pump sounds!? :P

Interesting that it failed on the dyno though, was the fuel pressure not being monitored or is it just one of those things?? Makes me want to check my fuel pump, though I have rewired mine and has been sweet so far.

That's what I mean though...040 is so cheap I don't know why people don't just go for that. Still using stock wiring at 260rwkw, no issues with fuel supply...will see if it lasts when I switch to ethanol.

Must have had a dirty tank Stao, or had the pump sitting right at the bottom. Nearly 2 years on and mine never whines!

Unrelated: gearbox running in period approaching it's end; have been giving my car more frequent bursts of full throttle. I've said it many times and I'll say it again, SS1PU ftw. Lastnight was cold as ice and she was throwing my mate back in his seat hahahaha.

If u put a flow gauge on aftermarket pumps with engine running u will see how much upgrading the wiring helps. Yes u can just do the earth mod but i always prefer running a relay with a strong battery supply.

That's what I mean though...040 is so cheap I don't know why people don't just go for that. Still using stock wiring at 260rwkw, no issues with fuel supply...will see if it lasts when I switch to ethanol.

Must have had a dirty tank Stao, or had the pump sitting right at the bottom. Nearly 2 years on and mine never whines!

Unrelated: gearbox running in period approaching it's end; have been giving my car more frequent bursts of full throttle. I've said it many times and I'll say it again, SS1PU ftw. Lastnight was cold as ice and she was throwing my mate back in his seat hahahaha.

Why not rewire yours? It's cheap and easy to do.

No need to, yet :/

Wouldn't wait until there is a need, by then it will probably be too late and a whole lot more expensive. You're probably wearing out your pump a lot faster by running it at low voltage, Bosch do say to run it at a minimum of 13.5v.

Hi, going to book a tune this week, just wanted peoples opinion on an ECU, I currently have Power fc with Z32 afm. But i was thinking to go down the path of Adaptronic and go with a MAP sensor?

What are your preferences, to help me make a decision, as i dont know what to pick. Its only between the two so please don't recommend another ECU

Both will give the same outcome. But u could sell the power fc, afm and boost controller if u have one and use the adaptronic with boost solenoid so it controls boost

I'm not going to be using a electric boost solenoid, so that feature will be void, but for tunerbility and power potential, would AFM (power fc) or MAP (Adaptronic) be better? If they are similar and outcome will be the same as you say, is it worth the hassle of selling the setup i have now and going Adaptronic? On a side note, Adaptronic uses wasted spark, will this affect life of the coils or produce a lot more heat in the engine?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
×
×
  • Create New...