Jump to content
SAU Community

Recommended Posts

That one is a bitch to change

Good luck

Thanks prob get some mates over so I don't have to do it all alone and to talk shit

Sorry to hear mate, Buy some gaskets and change anything suspect while your on the job :)

This will be the go if I'm changing that may as well fix the lot

G2.5 is a smaller turbo then a G3, they generally maxing out towards 260rwkws mark. So its about at its limit.

He's right, the graph shown is for a G3, but the intake leak might still be present and causing the 5ish psi boost drop. Fixing it might get him another 10-15kw from threshold to redline, definitely worth investigating.

http://www.hypergearturbos.com/atr43.html

The link says G3 but that is the graph from the G2.5 on the page. Either way I will suss out any leaks and give it another run soon.

That G2.5, I thought was a high flow. Preload the actuator about 10mms, if it starts to pin then its usually a restriction some where. This one don't have much of boost drop.

also stao,

your new website isn't meta tag searchable/ google submitted as i cant seem to find the new one on google which is meant to have more details on your range then the old website

That G2.5, I thought was a high flow. Preload the actuator about 10mms, if it starts to pin then its usually a restriction some where. This one don't have much of boost drop.

Hiflow of a stock 25 turbo? It has a 3 inch inlet so i don't think so

lol... does it fry tyres when you smash the pedal?

Yes it does, because the car is so big and front wheel drive, it wheel spins on the spot with stock tires. lol

Hiflow of a stock 25 turbo? It has a 3 inch inlet so i don't think so

Preload the actuator to about 10mms. If you a have a boost gauge, check the pressure drop before and after the cooler, also try a run with no exhaust on.

Yes it does, because the car is so big and front wheel drive, it wheel spins on the spot with stock tires. lol

Time for some M/T tyres? :P lol

This is for a good comparison of the new ATR28SS1 V ATR28G1 based on the Kia's G4GC engine:

SS1 at 8psi, G1 at 12psi:

ower:

Thin red: SS1 @ 8psi,

Green: G1 @ 12psi

Thick Red: NA none turbo @ 0psi

ss1vsg1power8psi.jpg

Boost:

Green is G1,

Yellow is SS1

g1vss1boost8psi.jpg

SS1 at 14psi, G1 at 12psi:

ellow: SS1 @ 14psi

Green: G1 @ 12psi

Red: NA @ 0psi

g1vss1power14psi.jpg

Boost:

Yellow: SS1

Green: G1

g1vss1boost14psi.jpg

This is an excellent turbo for around the 200rwkws on a SR20det.

I don't think that would be a problem. I can upgrade it to the latest profile, which is targeted at boost dropping issue with internal gate. PM if interested to go ahead.

Those are a set of CT20 Toyota Supra turbochargers that I've recently done. Those are rated to about 400HP each. Running ATR28G3 CHRAs. photos shown compressor and turbine wheel comparison, profiled compressor and turbine housings, and completed turbocharger assembly.

chra.JPG

turbine.JPG

housing.JPG

turbos.JPG

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...