Jump to content
SAU Community

Recommended Posts

Wut?

Not tune, set boost to afr? What you mean man?

Have you never done that or something?

You just talk to the car nicely, tell it what you want

Sometimes you plug a Vac line in the AFR gauge (make sure its narrowband) and it tunes for you

I mean use the wideband in ur exhust and work the afrs in turn the more boost you have the leaner ur engine will b to safely run most probs under 10psi so you dont lean it out so that was my question

I mean use the wideband in ur exhust and work the afrs in turn the more boost you have the leaner ur engine will b to safely run most probs under 10psi so you dont lean it out so that was my question

LOL, it's 2016 not 1984 tuning Pulsar ET turbos.

I mean use the wideband in ur exhust and work the afrs in turn the more boost you have the leaner ur engine will b to safely run most probs under 10psi so you dont lean it out so that was my question

Will the turbo do that? Or the ecu?

OK thanks, will there be much difference in performance over standard?

No differences works exactly the same. Need to make sure factory turbine housing is not cracked.

I mean if you put a bigger turbo on without the supporting mods computer injectors exc you can do this tho you cant run high boost cus lean out injectors max out so obd wide band goes up exhust and you use a hand held computer that tells you ur air to fuel ratios you can tell if its leaning or richining thats all im trying to ask if

Tao from hypergear has had any 1 do this with a high flow turbo

I mean if you put a bigger turbo on without the supporting mods computer injectors exc you can do this tho you cant run high boost cus lean out injectors max out so obd wide band goes up exhust and you use a hand held computer that tells you ur air to fuel ratios you can tell if its leaning or richining thats all im trying to ask if

Tao from hypergear has had any 1 do this with a high flow turbo

Don't do it, it's not a VL commodore.

Doesn't make sense at all, a bigger turbo will push more air into the engine, you'll enter a section of the fuel/ignition map in the ecu wich isn't even there. There's no sense at all changing turbo's without doin 'the complete package'. If it should be that easy, why would everyone put aftermarket ecu's in there cae ... ;)

Edited by Dr. Surge

Ok sweet well owning an auto stagea kinda makes things hard its a pigy back set up or full computer ==$$$ and the closest tuner is 500klm

Nistune will do auto transmissions, and flex fuel to boot.

If you think outside the box you can piggyback a full standalone ontop and let that ecu do all the work but the stock ecu for auto control. Then literally cut all the ignition and injector outputs from the stock ecu and wire it up to the standalone.

Always ways around it, just need to think outside the box. Also you can set the stand alone to input a gear change signal and retard timing for you so you don't grenade your box.

If you think outside the box you can piggyback a full standalone ontop and let that ecu do all the work but the stock ecu for auto control. Then literally cut all the ignition and injector outputs from the stock ecu and wire it up to the standalone.

Always ways around it, just need to think outside the box. Also you can set the stand alone to input a gear change signal and retard timing for you so you don't grenade your box.

My box is fine. It only retards timing at wot anyway. I don't believe the adaptronic is capable of retarding on gear changes anyway, according to Andy.

And yes everything is run through the new ecu except for idle so the auto knows when it is in gear and obviously the auto control.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...