Jump to content
SAU Community

Recommended Posts

It saves weight if you don't carry beer with you, buy it at the destination. My point is a modern medium/large suv makes a great tow bitch, way better dynamics, fuel economy and comfort compared with most ladder frame 4x4's. Particularly something with a V6 turbo diesel, struggling for power is a pain on a long trip..

Lol, what's this new trailer called, B Double?

Solar powered fridge is good, the lift pump battery on my trailer is charged by solar power which saves a lot of stuffing around on a trip.

Edited by 260DET
  • 5 months later...

I'm a towing newb. 

Our 'big car' is a Mazda CX7. Be kind. Would you tow a car behind it? 

That said, I think its only rated to 1700kg's braked, which doesn't leave much for a car considering the weight of the trailer. :(

 

 Not a great choice in my opinion mate. Even towing the R33 with my pretty heavy Ranger Ute I can feel it moving me around a bit on the road. A light little SUV like a CX7 would be dangerous in my opinion. A good gust of wind and you’ll be on the other side of the road!

The average car weighs around 1400-1500kgs so you’re right, it doesn’t leave much room for the weight of the trailer if the total is 1700kgs!

I'd do it one-off for slow and shorter trip, but not regularly. For a start most car trailers are 500-800kg so that means the car you are towing is limited to 900kg. And even then when you tow right up to the load limit you often learn that while the chassis can take the load, the engine won;t deliver the performance to tow it safely (hello creeping up hills on the freeway)

On 6/15/2018 at 10:40 AM, fatz said:

True

if your under 5’8 go defender

 

if you any taller you won’t fit

Or if you enjoy punching the underside of the dash with your knuckles ever time you put the handbrake down.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...