Jump to content
SAU Community

Recommended Posts

Probably just because I like to over do things.

The logs from the Motec at Winton showed that it was dropping oil pressure under brakes and I'm not entirely happy with the pressure that it's pumping given that the engine is new and the relief spring is already shimmed up. It's running Spool spline drive pump gears and I'm just not super confident that it's all 100%, so I'd prefer to dry sump it. The sump is from Lewis Race Engines, and it's had a couple of pin holes in it from new which I've had to braze up.

So I just wasn't super happy with the whole setup, so although it's going to be $10k, I reckon it's money well spent to ensure that the engine holds together a bit longer. I have gone with the Ross / Aviaid system because I've already got a Ross balancer so the mandrel will be a simple fit, but if I had more spare time for fabrication and fiddling I certainly would have got a nicer pump than the Aviaid with rootes scavenge instead of spur gears.

Also, I have now trumped you in over capitalisation on an HCR32 and have the most highly polished turd around. All I need now is a sequential dog box....

I don't have any pics of the Lewis sump but I'll take some when I pull it off in the next few weeks.

It drops pressure under brakes, fine in the turns. I actually suspect that the pump is more the issue, but without pulling it off I'll never know and the crank has been fitted with the Spool spline drive mandrel which means I'm kind of stuck with that unless I want to take the crank out. I don't want to do that, so dry sump is the best option. Not the cheapest option, but I won't have to worry about oil supply and pressure again so it's worth the additional expense.

  • 4 weeks later...
  • 3 weeks later...
  • 1 year later...

Well back in Melb, got my gearbox back in after being pulled apart again. Now to tidy up a few things and get ready for the Bend in June. 

 

Can't wait to get the bus back on track. If anyone has some old school wheels then I'm on the hunt. I'm blown away how hard it is to find period wheels these days

  • 2 months later...

Well after working in regional Victoria for the past 2 years finally starting to get home and get some work progressing on the car. Finally finished the wiring of my surge tank.   Worked great at Phillip Island and first day the quick connect on the return line made a breeze to drain tank after a session and work out fuel used. Ended up being able to easily work out the fuel required for 12 lap sessions during the recent 6hr and pitted with only about 5 litres left in the car. 

 

Needlessly complicated actually had good functionality :)

 

And https://www.jrmphotography.com.au/ always delivers on the photos front :)

20220724_173014s.jpg

PhillipIsland6Hour2022-44.jpg

PhillipIsland6Hour2022-121.jpg

PhillipIsland6Hour2022-39.jpg

  • Like 9
  • 2 months later...

So pulling the Racetech seats with wings out and trying to make a little more street car.  Lol, only prob is i dont have seat belt buckles to bolt to frames. Anyone with any spare or ideas on whete to get a pairbof buckles cheap

 

Once in need to get them trimmed to match...auto trimmers aint cheap

 

 

received_3289873211342069.jpeg

received_529220729038794.jpeg

On 10/18/2022 at 8:59 PM, Roy said:

So pulling the Racetech seats with wings out and trying to make a little more street car.  Lol, only prob is i dont have seat belt buckles to bolt to frames. Anyone with any spare or ideas on whete to get a pairbof buckles cheap

 

Once in need to get them trimmed to match...auto trimmers aint cheap

 

 

received_3289873211342069.jpeg

received_529220729038794.jpeg

absolutely love the CS Sportsters. do they drop in easily? plenty of clearance from side of seat to door etc?

On 10/18/2022 at 7:59 PM, Roy said:

Anyone with any spare or ideas on where to get a pair of buckles cheap?

I have found pulsar and patrol buckles to work with my s chassis seat belts in the past. Need some modding to get the length and bolt hole right.

Those recaros are so good, love them in my Z. Shame no provision for a 5/6 point harness.

On 10/20/2022 at 7:27 PM, Roy said:

The Recaro CS were shits to fit. The seats fit thevdimensions of the car well but the rail design and getting seat low is the usual head feck

Yeah. I had the same fitting some CF Bride reps into mine. Ended up doing some very small mods to be able to run without some thick washers that are "required" to fit the seat to the rail. Gained myself a few mm, still feel like they're too high.

Didn't want to go for the "ultra-low" rails as they are a different type of headf**k.

  • 1 month later...

So after being ready with a week to spare before Bathurst, the car developed an oil leak that took 3 days to diagnose  Tried lines, gaskets and in the end it was a hairline crack in the alloy housing that bolts to the block that you screw your filter too. Was a bastard to diagnose. LOL , may need to make a longer oil cooler line and install one of those billet ones.

Then on to Bathurst. Car was running like a dream. First 3 sessions were either red flagged 2-3 laps in or just too much traffic and was forced to clear the slower cars until the re-categorised starting positions on the dummy grid. For session 4 they bumped me up 18 spots right behind a Cup Car on slicks. Was pumped and was hoping to finally get a good run without traffic.

On the first flying lap at the top of Mountain Straight the engine went flat and had no drive at turn in to Griffins Bend so had to do a Glen Seton 1995 and pull over in the gap in the concrete wall on the right to the end of the session.

So lost injectors for some reason so started pulling back all the loom tape trying to find the short. Couldnt see anything , so called it at 9.30pm and went for beers.  In the morning re-taped the loom and had injectors back!!!!  I hate it when things start working for no reason...I hate it more than when they stop for no reason :)

So waited to the afternoon session, spoke to drivers around me to make sure that I could find a gap and tried my luck for a single lap.  LOL i am guessing it was a combination of heat, vibration etc that something is shorting and popping the Engine Con fuse so with very few plces to pull off the track and too many walls to be losing drive and power steering etc only wasnted to do one flying lap

 

So this is the vid of that lap that ended up as a PB...sooooo much left in it. Will have to go back next year after i put a new loom in the old girl over Xmas

 

Even though the morning 3 sessions were red flagged etc the running around with Porsches and big HP Evos was the most fun I have ever had in the old girl

 

 

  • Like 5

Sucks about the wiring issue, good excuse to make a new one and maybe upgrade the power fc 

Looks like heaps left in lap time, be an awesome place to drive. Hopefully see you there next year.

I'm too big a tight ass to do anything ECU wise. Power FC gets the job done. By the time I do an ECU. Loom, trigger etc it's 5k that doesn't make the car any faster as I really don't need more hp.

 

I'll pull the loom from the car and strip the loom this weekend . Also need to do a fre checks on the engine. Doing a hot shut-down at Griffins Bend wasn't ideal. Lifters were loud and engine  a bit cranky when I got it fired back up the next day

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...