Jump to content
SAU Community

Recommended Posts

I fitted a Boost gauge to my stag at work tonight. drove home, standard solenoid standard turbo - 10 psi. strange. now i just gotta try and work out why it's running so much boost, either a faulty gauge or it has an rb20det boost solenoid fitted.

I fitted a Boost gauge to my stag at work tonight. drove home, standard solenoid standard turbo - 10 psi. strange. now i just gotta try and work out why it's running so much boost, either a faulty gauge or it has an rb20det boost solenoid fitted.

i grounded out the solenoid via a switch so i can run low or high boost which happens to be about 5-7 for low and 10 for high

i also have an electronic boost gauge and would happily swap it for a normal one

where did you guys take the boost reference from? mine is plugged into the drivers side rear of the intake manifold right next to the brake booster piping. might try putting a t- piece into the boost sensor hose and see if it reads different.

very surprised it didn't fit - every skyline brake bit I've put on mine bolted straight on....I've run gtr front and rear brakes on it now?

what was the problem, did the adapter hit on something? Either way Im sure UAS will refund.

Hi guys with slight mod they do fit . But once on the spacing is 11mm off . Even with a spacer the disc wont fit under the caliper without fouling .

did an oil and filter change today

guld western s6000 sougi - awesome stuff

car runs sooooo smooth

$68 and its the same spec as motul 300v or royal purple (shits all over penrite, nulon, castrol etc)

Hi guys with slight mod they do fit . But once on the spacing is 11mm off . Even with a spacer the disc wont fit under the caliper without fouling .

You are running the skyline disc to suit that kit not the stag one right? They need to be changed as a pair

Spent 8-9 hours at custom exhaust shop standing around and helping out getting new front pipe made, cut and reweld my new exhaust which was bent in 3 places and new/modify intercooler piping to suit new turbo and front facing inlet plenum

You are running the skyline disc to suit that kit not the stag one right? They need to be changed as a pair

I am using a 324mm skyline gtr disc & sumitomo calipers off a skyline . So i think am using right parts but any advice would be appreciated.

Well today I have finally finished the Front Facing Plenum fit out complete with a FMIC. It has been quite a long project

as being 50ks from suppliers is a bit of a drag. Every time you need a bit it is a 100k round trip.

Anyway I am happy with the way it has all turned out. I will have pics of it next week when we do a road test. My boys are off to Eastern Creek tomorrow in the 25G.

Spent an hour last night relocating (slightly) and refitting the handbrake assembly, for my modified manual console surround (grafted the Stagea auto surround and an R34 manual surround together). It all fits and now I just need to improve it cosmetically. Got some leather boots for the stick and handbrake with red stitching coming from ebay, and I'm also fibreglass puttying up the console to sand it back to a smooth finish.

:ermm:

Spent an hour last night relocating (slightly) and refitting the handbrake assembly, for my modified manual console surround (grafted the Stagea auto surround and an R34 manual surround together). It all fits and now I just need to improve it cosmetically. Got some leather boots for the stick and handbrake with red stitching coming from ebay, and I'm also fibreglass puttying up the console to sand it back to a smooth finish.

:down:

Pics please!

Well I thought I would kill a couple of birds with one stone. I needed a new GPS and car kit.....easy answer Garmin 1490T(great unit)....but I also wanted an Greddy Infometer.

It had been mentioned to me that Garmin will be coming out with an OBDII port dongle....http://www.ja-gps.com.au/Garmin/ecoroute-hd/

Anyway that day arrived yesterday and as I received the much awaited package and unwrapped with excitement then hooked it up. I soon came to the conclusion the ecoroute-hd didn't work. F#$KING M35's!!!!!!

I did decide to test it on some other cars though......much to my joy :down: (not to my mates)....it doesn't work on a V6 commodore either....and I cannot even find the OBDII port on another mates Mitsashitty 380.

Pity this would have been awesome for the price

Plenum in. Started the Stag. Took a few turns to get the fuel up. Ran like a dream up to 2500, then total misfire. WTF.

Checked all connections and found AFM plug not in socket properly. Clicked in and PRESTO. Music to my ears.

Get the wheels on then off for a drive.

Polished up the brembos today and they are in awesome nick! no marks at all :D very happy.

All the braided lines (approved) are here, just waiting on the rear caliper bolts to come through Nissan from Japan.

Clean pic below!

post-4475-1274338547_thumb.jpg

Edited by bbenny

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...