Jump to content
SAU Community

Recommended Posts

Get some neg camber on that sucker - STAT!! 4mm different offset than mine (+22) and your's is full mexican!

I fitted my bluetooth adaptor for the headunit, so now I can take and make calls without worry of getting busted on the phone.

i will hit the coilover soon enough if i put too much in... its got like 1.5 degrees now so NOTHING... just lipped the gaurds more and not touching at all anymore :)

they were +30 with a 5mm spacer.

So that confirms the ideal M35 fitment as 9.5 +35 offset.

Oh and they look insane! so tough!

come again?

if they were +30 and he added a 5mm spacer, that would mean that they are now sitting effectively at +25

or if they are +35 with a 5mm spacer then they would be effective +30

etc

finally got around to aligning mine, and very happy - exactly what i wanted (well maybe closer to 3 deg neg on front but 2 is fine) :P

18x9.5+2

18x9.5+1

front -2 deg camber

rears -.5 deg camber

100_1405plateless.jpg

100_1413plateless.jpg

100_1409plateless.jpg

how the driveway go mike?

yeah not too bad, no dramas getting out and only a little bit of rubbing from the front bar getting in surprisingly.

the wheel aligners was another story.. had to have a couple of blokes push me up their driveway cos i got beached sea-sawing :ph34r:

I accidentally bought some wheels when I went to get a fresh set of tyres... 19x9.5 +35 with 5mm spacer on all 4 fit peeeeerfect.

stagea.jpg

I will get some better photos soon.

NICE!!!

might have to do my headlights soon!.....once I stop buying other parts!!!

I accidentally bought some wheels when I went to get a fresh set of tyres... 19x9.5 +35 with 5mm spacer on all 4 fit peeeeerfect.

stagea.jpg

I will get some better photos soon.

LOL @ "accidentally" bought new wheels...

LOL @ "accidentally" bought new wheels...

lol I just accidently bought a 15g R33 GTR

going to sydney soon to pickup

must sell the track car now

currently fitting wilwood brakes, to put the brakes back on the r32.

might end up selling the stagea if I enjoy the gtr too much. or vice versa

Well it seems I need a different loom and a relay of some sort. :D

do you mean you're putting in the little motor that helps close that last little bit or the one where you push the button and the whole tale gate opens and closes?

if its the latter, where did you get it from and how much? i like gadgets :P

Well it seems I need a different loom and a relay of some sort. :wub:

If you can get a part number (and a picture) for the relay i have a box full of relays and resistors and other odd little electrical boxes left over from my wrecked car!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...