Jump to content
SAU Community

Recommended Posts

My gut feeking is that Garrett have a bit too much compressor capacity in a "GTX3076R" and their partial fix is to use a GT35 turbine with the "76X" wheel to get GT3582R type performance .

Time will tell if the GTX3071R becomes the replacement for the GT3076R 56T .

Its more than a gut feeling, that is why the newer gtx3576 was released, I don't think the results from the gtx3076 were at all good and Garrett cant afford to release any more poorly performing turbos . I cant seem to find any decent graphs for the GTX3576 though. In theory it should get close to 400kw on e85 right?

I feel I have maxed the gtx3071 compressor, not sure if I want to go bigger yet or not. I was hoping to fine tune it up to 350kw but squeezing that last bit will be hard as i'm changing back to the .82 housing soon.

Its more than a gut feeling, that is why the newer gtx3576 was released, I don't think the results from the gtx3076 were at all good and Garrett cant afford to release any more poorly performing turbos . I cant seem to find any decent graphs for the GTX3576 though. In theory it should get close to 400kw on e85 right?

I feel I have maxed the gtx3071 compressor, not sure if I want to go bigger yet or not. I was hoping to fine tune it up to 350kw but squeezing that last bit will be hard as i'm changing back to the .82 housing soon.

A GTX3576 should easily hit 400rwkw on E85 you'd think? Given a run of the mill GT3076 on E85 will do 330rwkw or there abouts on it.

You'd need to be running some decent boost of course.

Why would the GTX3076 be a bad option then? I'd love an easy 360-370rwkw on E85. Maybe even get a little crazier and put a 0.63 rear housing on and see how it goes.

350rwkw with the launching ability to out pace a cruise missile over the quarter mile?

I made a bit over 320rwkw on a 0.63 rear on a RB25 completely stock. 22psi. About 750nm of torque. Water meth though.

I know the exhaust manifold pressures will be high, but I think the lower temps of the E85 should counteract this a little bit. Or I could be wrong.

I reckon I could have got close to 350rwkw with E85 on that setup.

Another gut feeling is that with the larger 1.06 AR Garrett GT30 turbine housing you could get a bit more squirt out of a GT3076R or GTX3076R . As has been said before other compressor upgraded GT3076R style turbos have used the larger T04S compressor housing and they would not do this without good reason .

Don't forget that these 0.70 AR comp housings were standard fare on turbos using the old 409535-1 (60-1) compressor wheels and they are ~ 76mm OD . Same deal with the er 7/14 bladed versions of the "GT3076R" turbos .

I think it depends on what you're trying to do , if its just maxing the turbo then the largest available housings are probably the best way to achieve that .

Most people have issues with turbo lag doing that and with good reason , out of most of you I think Mr Mafia is one of the few who quotes torque figures and torque is god as far as I'm concerned . I think he's right saying that E85 is a good way to decrease combustion temps and therefore EGTs and this would count for something when using not the hugest turbine housings .

It would be interesting to try a GTX3076R with a larger compressor housing in 0.63 and 0.82 sized Garrett GT30 turbine housings . If money was no object a decent exhaust manifold flanged to take the Evo 10 style Garrett 0.94 AR twin scroll twin integral wastegate GT30 turbine housing would be very interesting particularly burning E85 .

Mafia your R33 must have been a bit of a missile with the 0.63 and WMI combination , feel sorry for its rear tyres .

Sadly Garrett never made a T3 flanged 0.73 AR GT30 turbine housing , HKS did make that size but in T2/25 flange and no integral wastegate . People who used ext gate GT3037s liked 0.73 turbine housings and on SR20s the 52 comp trim ones were torque mountains - for an SR20 anyway .

Cheers A .

Most people have issues with turbo lag doing that and with good reason , out of most of you I think Mr Mafia is one of the few who quotes torque figures and torque is god as far as I'm concerned .

tractive effort not torque.

I had a not bad experience with my old setup.

RB25\30

Ported exhaust Ports

Ported exhaust manifold

GT3076 56trim, 0.6 Surge slotted Cover, 0.82 Int gate rear housing

256in/ex poncams

No water meth

Vipec

Vipec Boost control kit

Ignore the drop off at the end - The dyno straps were a little loose on the last 2 runs and the drop in load caused the boost to drop off a little meaning the torque follows suit too. Most runs it stayed flat all the way to the limiter.

312rwkw.jpg

Edited by The Mafia
Most people have issues with turbo lag doing that and with good reason , out of most of you I think Mr Mafia is one of the few who quotes torque figures and torque is god as far as I'm concerned .

Plenty of us refer to power at particular points in the rpm range, which is probably more definitive than the tractive effort readings the dyno puts on a "torque" curve as you can't really compare those numbers between dynos or necessarily even the same dyno with different cars.

I think he's right saying that E85 is a good way to decrease combustion temps and therefore EGTs and this would count for something when using not the hugest turbine housings .

Absolutely he is - I take quite different considerations when matching a turbo for something running pump gas vs E85 etc, I picked a .82a/r hotside for my car partly because I was going to be using stock manifolds and pump gas on a motor with cast pistons etc. E85 is amazing stuff, I wish we had it at the pump here.

It would be interesting to try a GTX3076R with a larger compressor housing in 0.63 and 0.82 sized Garrett GT30 turbine housings

As I've mentioned before, ForcedPerformance imho have done a better job with the GT30 and GT35 "improvements" than Garrett - and they use a modified .70a/r T04S cover for their GT30 varients, there have been some very impressive results for their GT3076R-HTA running .82a/r hotside. If money was no object, I'd try one of their GT3073R-HTA turbos out on an RB25 - could be interesting.

Quote

Disco - why the affinity with internal gate turbos?

If a custom manifold is needed why not go external/twin external gate and reap the benefits

Because not everyone wants the trouble and expense of external wastegate/s . The only reason I suggested a one off manifold is because nothing short of an Evo 10 manifold fits the only Garrett twin scroll twin integral gate GT30 BB turbine housing made . If they did one in twin entry T3 flange it would be even easier , how many of you could resist a twin scroll twin IW turbine housing that fitted your std exhaust manifold ? More torque and better turbine response than your getting now with single scroll housings and how cheap and easy compared to two external gates and the extra plumbing they need .

On a trailer sailer it doesn't matter but on the street it does .

Tractive effort is that which is needed to harness high torque , the best you're gonna get there is AWD in anything street driven . A wise person once said to me that AWD was the best answer to turbo torque on the dirt and thats why all the decent rally rockets went to AWD . Not the go for all out tubbed drag cars but thats so far away from anything with number plates anyway .

I reckon without front wheel drive on the track a GTR would just be a larger Sierra .

In the locomotive world they measure tractive effort in thousands of pounds - in the US anyway . The other way is to look at a percentage of the beasts gross mass in its draw bar pulling capacity . So say 30% of a 132 tonne unit = lots .

Recent tests our mob did with AC traction units showed the horse derated itself from 4400 to 2750 Hp just to hold its feet . What this shows is the difference between power/torque and tractive effort , how you go about getting your power to the ground is a different issue .

A .

Its more than a gut feeling, that is why the newer gtx3576 was released, I don't think the results from the gtx3076 were at all good and Garrett cant afford to release any more poorly performing turbos . I cant seem to find any decent graphs for the GTX3576 though. In theory it should get close to 400kw on e85 right?

I feel I have maxed the gtx3071 compressor, not sure if I want to go bigger yet or not. I was hoping to fine tune it up to 350kw but squeezing that last bit will be hard as i'm changing back to the .82 housing soon.

Where is the evidence to prove a GTX3076 is a "poorly performing turbo" ?

Is there any strong evidence here or just guess work, if it has performed poorly is it because of the turbo or someones lack lustre setup? according to the flow maps it is just as good or even better than a GT3076. And for upto 350Kw surely it is a Very Good performing turbo.

the compressor side isnt the issue, I'm sure the compressor wheel is great like most garrett GT turbos

the turbine side is not so great

so combine a not so great hot side with a really good comp side...and they don't perform like they should

hmm, well my car is untuned and unfinished but i have the gtx3076 0.82, external gate , cams etc , should i be sourcing the normal compressor wheel and put it on so i have more of a compressor match to the turbine side? cause id like the best result possible with response.

or should i just see what happens with it?

Edited by SliverS2

I have tried quite a few combinations of turbo out so far and what I have found is if you restrict the turbine the top end will be limited. According to the compressor map the GTX3076 should flow like a GT35 so why doesn't it? The rear is simply too small.

With the GTX3071 the extra compressor flow was compensated by upping the cropped turbine wheel to a full GT30 60mm version. It seems to have made it behave like the GT3076 but with better response. If this new GTX3576 can do the same, flow like a GT35 but with better response, it may be the turbo of choice for those chasing 350-400kw+.

hmm, well my car is untuned and unfinished but i have the gtx3076 0.82, external gate , cams etc , should i be sourcing the normal compressor wheel and put it on so i have more of a compressor match to the turbine side? cause id like the best result possible with response.

or should i just see what happens with it?

Thats not to say your GTX3076 is crap, it just doesn't live up to its hype. These turbos were supposed to be on another level which the 71 seems to be but the 76 was just restricted a little too much. At the end of the day it will make good power but not what the compressor is capable of making. Go for it, tune the sucker, you wont be disappointed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...