Jump to content
SAU Community

Recommended Posts

Nice josh they fit in well but are very low! I suggest some spacers [emoji6] they are much nicer than mine. Got mine for $150 but they are stained from the cover the guy had on them. Looking into dying the leather as cleaning then with a tonne of elbow grease has done nothing.

Edited by Lakes101

Nice josh they fit in well but are very low! I suggest some spacers [emoji6] they are much nicer than mine. Got mine for $150 but they are stained from the cover the guy had on them. Looking into dying the leather as cleaning then with a tonne of elbow grease has done nothing.

By my measurements; they look to be about 50mm lower at the seat base?

Nice josh they fit in well but are very low! I suggest some spacers [emoji6] they are much nicer than mine. Got mine for $150 but they are stained from the cover the guy had on them. Looking into dying the leather as cleaning then with a tonne of elbow grease has done nothing.

Yeah thats good to hear. Id rather the lower sitting to the stock stagea seat clearance as i feel now its too high. 50mm will be perfect. Cant wait to get my hands on them. Quick clean and then install.... bring on October and WTAC

  • Like 1

Hey guys

I'm new on here, but not new to the 'import car scene'. I've had a Supercharged AE86 and a '99 S15. Just picked up a 97 S1 C34 Stagea last Friday. It was a bit rough when i got her, but i'm slowly cleaning her up

So far I've swapped the cheap tiny dirty excuse of a pod filter for a K&N and cleaned the air flow meter at the same time, Pulled out the HID Head lights with no High beam and replaced them with legal standard bulbs (i have high beam now surprise surprise!), only about 2 bulbs in the AC unit worked, so I put new bulbs in so i can see it at night(I wrecked one blue condom thingy, so if anyone has some they don't want, let me know!), the car had no Floor mats so i got a full set of c34 mats for it, installed a M80 mongoose alarm

and today at lunch i went home and pulled the old falling apart steering wheel off and put on a MUCH better condition one!

fV7fAyG.jpg

XIV818F.jpg

I have no idea how to upload photos to SAU sorry, so sorry if they're huge

  • Like 1

Gave the Stag a wash and touched up a few chips and scratches today.

Also changed my fuel filter and drive belts which were on their last legs.

Nothing says JDM like finding some yen under the back seat.

post-135423-0-35647600-1442051713_thumb.jpg

I'll be tackling the dump/front pipe next weekend (not enough time today and going to Shepparton swap meet tomorrow to buy more crap that I probably don't need)

Still by far the best upgrade I.m.o.

Response from mid to top end very tidy indeed. For me paired to the aftermarket 3" exhaust my fuel economy improvement has been the real big bonus tho...

Still very happy customer

How much better is the feel economy with this done vs stock?

?L/100km

How much better is the feel economy with this done vs stock?

?L/100km

My fuel consumption went up to about 13.5L/100km around town after doing the Transgo shift kit install (stock exhaust, cheap air filter)

Is now down to about 12.5 around town after installing the Blitz panel filter and Nismo mid pipe and muffler.

Interested to see how much difference the dump and front pipe make.

dammit....what I did to my stagea lately is blow the damn turbo...the bearings are totally rooted.

so basically, I got to spend sunday morning pulling the tow car apart instead of the race car

turb_off.jpg

and off to get it rebuilt tomorrow I guess. hopefully the turb bearings in the oil didn't hurt the motor

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...