Jump to content
SAU Community

Recommended Posts

Yeah mine are done by these guys on St Kilda road http://www.visioneyeinstitute.com.au/locations/victoria/melbourne/ they're meant to be the best in Melbourne.

I think it was a bout 5.5k it's great I highly recommend it. Going on about 2 years now.

I've heard the same about vista eyes lol

Yeah mine are done by these guys on St Kilda road http://www.visioneyeinstitute.com.au/locations/victoria/melbourne/ they're meant to be the best in Melbourne.

I think it was a bout 5.5k it's great I highly recommend it. Going on about 2 years now.

I'm looking at going to vista later in the year

Yeah i looked into most clinics in Melbourne. Price rangs from $4k to $5.5k

I have a client who does it but he charges a premium

There is a groupon offer for $3.75K but not sure of the quality

I found a reputable place in Sydney that does it $2.5k that i have heard nothing but good news. But then need to factor in hotel and flights


11578-brucie_gta4.jpg

Genetically Superior Baby!

That man has boobs.....

Anyone know where I can get a small tin of plastidip locally? Or anyone have any that I can use a small amount of?

yep....autobahn....or The body shop actually stock a similar product now too...meant to be better ...well thats their sales pitch anyway

That man has boobs.....

yep....autobahn....or The body shop actually stock a similar product now too...meant to be better ...well thats their sales pitch anyway

Interesting, not in a spray pack though? I need a tin of the stuff. The body shop? Isn't that a girls soap shop?

Anyone know where I can get a small tin of plastidip locally? Or anyone have any that I can use a small amount of?

think i have half a can (spray) of black plasti-dip brah, can check the garage to make sure.

Interesting, not in a spray pack though? I need a tin of the stuff. The body shop? Isn't that a girls soap shop?

its also a paint supplies shop...seaford one has plastidip stuff...not sure if dandenong has it...pretty sure autobahn has it now anyway

Yeah i looked into most clinics in Melbourne. Price rangs from $4k to $5.5k

I have a client who does it but he charges a premium

There is a groupon offer for $3.75K but not sure of the quality

I found a reputable place in Sydney that does it $2.5k that i have heard nothing but good news. But then need to factor in hotel and flights

Things I liked about Vista are they have the wavefront analysis, and rick wolfe has done shit loads of these. At the time I think it was about 6k all up, but that was 5+ years when I had that check.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...