Jump to content
SAU Community

Recommended Posts

Maybe try some A050's , though I've heard they're not very good in the wet either :rolleyes:

ao50, if the road isnt like a lake, theyre awesome in the wet.

also. wtb. security guards.

Dat Taga prepped 34R was pretty farken planted on the deca skid pan that super wet deca last year where the skidpan pretty much was a lake lol.

Also, just bought another RS this morning, flying to Shitney Saturday to pick it up

One day you'll have an RS actually on the road... and that day shall be sweet

Well, he had one on the road.

I'd know cos I raped the clutch a bit.

Nah I'm probably going to revert mine to stock and sell mine, this one cost me pretty much the same coin and is far tidier, also has sunroof.

whats not stock about yours?

didnt you do this with the last RS you had? (except was damaged) whens it going to stop miguel, when is it going to stop?

whats not stock about yours?

didnt you do this with the last RS you had? (except was damaged) whens it going to stop miguel, when is it going to stop?

gc8 4 pots, gc8 susp, gc8 steering rack, whiteline alk, resonator deletes, 3"tbe, f&r strut bars, koyorad, alloy rear swaybar c links. Will all make their way onto new wun whiteline f&r swaybars it already has. stock bits onto grey one.

This will be the end... curent one was supposed to be the end too but they're so much car for the money gaddamit.!

whats not stock about yours?

didnt you do this with the last RS you had? (except was damaged) whens it going to stop miguel, when is it going to stop?

its like we're losing you Miguel. Enough is enough.

Depending on insurance situation and love for the vehicle of course...

The missus had third party fire and theft on it so it's covered for 3 grand worth of damage. Luckily I was on the policy so I could sort stuff out without her here. Fingers crossed it's not written off but they did a nasty job inside the car.

She loves the car though so it's going to be rough breaking it to her when she comes back from her cruise tomorrow.

Our lease is up in Feburary so I think i will look at a better suburb. Didn't really do too much research when we first moved here at the start of the year.

Our lease is up in Feburary so I think i will look at a better suburb. Didn't really do too much research when we first moved here at the start of the year.

I tried that and had my car stolen lol, good luck brah Edited by HEKT1K

I'd do one for my R33 but it'd just bounce up and down too much to make sense.

Hell it's dropped 3 times since I've owned it, and when I bought it in 2010 it had "84600" after being imported with "54000" in 2006.

Yeah ok....

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...