Jump to content
SAU Community

Recommended Posts

4 hours ago, Dose Pipe Sutututu said:

Is this your car?

https://www.gumtree.com.au/s-ad/wahroonga/cars-vans-utes/2002-nissan-s15-200sx/1251512935

I guess I was wrong with the Samsonas and the power, but 506kW was close enough.

image.png.7955f677222e9705a65d51c5dbb47d5a.png

506kW..."Never thrashed or abused" LOL

$75,000... double LOL

 

  • Haha 1

It’s running. Starter motor was buggered, new one has been installed and a new TPS also.

Dyno on Friday I’m dropping off 100L of fuel tomorrow and 3 canisters of NOS , gonna need a 200 shot to make the numbers 

6 minutes ago, acsplit said:

Scott's Dyno magically kills starter motors.

 

*Looks at the emtron fanboy with his gtr*

& Racepace kills motors, pls.

Emtron is #1, move over Motec there is a new playa in town.

Once i started boasting about them online years ago before I even ran one everyone followed.

3 minutes ago, r32-25t said:

That’s the only thing you seem to be able to fault with the haltech and yet the best engine management system in the world uses multiple boxes 

Yeah I can't fault them for forgetting tunes. Oh wait yes I can... Multiple times actually ?

Edited by Mick_o
1 minute ago, r32-25t said:

Oh the vcam tune it forgot that turned out to actually be an issue with the vcam itself 

No there was more to it than that. And that was only 1 incident. There were a few attempts to add new firmware patches etc prior. Luckily his coils weren't fried when adding said firmware updates... 

  • Haha 1
6 minutes ago, Mick_o said:

No there was more to it than that. And that was only 1 incident. There were a few attempts to add new firmware patches etc prior. Luckily his coils weren't fried when adding said firmware updates... 

Like how all Ecus should have the coils and injectors disconnected when setting it up?

  • Confused 1
Just now, BakemonoRicer said:

Haltechs aren’t even worthy of being put in Silvia’s honestly. They are the power fcs of today’s ECUs, if you’re a big hitter you obviously run emtron 

If you’re a bigger hitter you run MoTeC 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...