Jump to content
SAU Community

Recommended Posts

And that's why you v the cam

haha, you got it Pete

Should pick it up on Monday, busting to drive it back home and then the other crap starts with the old builder to sort out the leak problem that cost me heaps of $$$$s , plus had my car off the road for 7 months

haha, you got it Pete

Should pick it up on Monday, busting to drive it back home and then the other crap starts with the old builder to sort out the leak problem that cost me heaps of $$$$s , plus had my car off the road for 7 months

I cheated and had a look see when I was at the house of jez last time
  • Like 1

Definitely flattened out that bottom end nicely would be mad to drive.

Do you think the 14 kilowatts was lost in the lack of lift in the intake camshaft?

I'm assuming you had the same size lift intake and exhaust on the old Dyno run?

I had the UE 260 10.8 cams with a sharp ramp rate, left the exhaust cam in

I was playing around, lol It is now a V-Cam Step 2 , 262 x 8.7 intake cam and using the same UE exhaust cam 260 x 10.8

Lost a little up top due to the smaller intake cam, would love to be able to use the 260 10.8

After waiting for months to find and start fixing the water leak I had too much time on my hands and thought , since the motor is out and the car was going to be in the shop for a while, I had plenty of time to order the V-Cam and get all the bits ready to plug in when it was going back together.

All run in and just about ready to go, couple of days to tidy it up :)

Pink old setup

Red vcam on

Green vcam off

Once Jez finally got the motor back he just got stuck into it :yes: this bloke is tops :wub:

post-52098-0-18833500-1457692150_thumb.jpg

  • Like 1

Was 8.7mm lift the biggest lift you could use?

You can get the "Pro" kit which has a 264 @ 10.0 mm but the price jumps up by another 50% or so. It comes with an ECU (which you cant option out) that you pretty much throw in the bin.

Worth noting is the little difference in power when going from a huge lift intake cam to almost an oem std spec intake cam, despite the slightly longer duration.

I agree and there where lots of things I could have done to make more power up top, bigger turbo and injectors were needed if I wanted to do anything as they were close to maxed out before the V-Cam and if I used the Pro I would have had to change them to get the benefit of the 10mm lift, I will never know ?

Photo of it being finished off. I even had strife with rocker the covers , waited forever to get them powder coated and when they arrived they were dinged :(

The Step Pro gives you more up top I think with the higher lift but only gives 300rpm over the step 2. Both give you a variable amount of 50deg. I was only after a better bottom end I went for the Step 2 and a lot less expensive.

It was hard to find out anything about V- Cams , so I had to wing it, bite the bullet and do it.

Paul might be coming up here at Easter and he can give an independent assessment of how it goes, just have to stop him and Mick-o from smashing the box,lol

post-52098-0-97918000-1457723898_thumb.jpg

  • Like 1

Good that you can finally drive it now after all this time[emoji106]

Cas is in the fully advanced position, was the ecu's timing locked and base timing set correctly prior to tune?

Edited by mr skidz

Good that you can finally drive it now after all this time[emoji106]

Cas is in fully advanced position, was the ecu's timing locked and base timing set correctly?

I bet my nuts it's set correctly.

Tuners do that so peanuts can't advance the timing by rotating the cas.

  • Like 2

Oooo I will be at Jez's Monday Pete, hopefully will see you there! I saw the Vcam ages ago but had to keep my mouth shut haha. Looks like you finally got the results you deserves right from the start! Shame you had to go through so much bullshit to get there.

Oooo I will be at Jez's Monday Pete, hopefully will see you there! I saw the Vcam ages ago but had to keep my mouth shut haha. Looks like you finally got the results you deserves right from the start! Shame you had to go through so much bullshit to get there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...