Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
On 22/08/2020 at 10:16 PM, Dose Pipe Sutututu said:

So PPG then?

PPG > Swimming Pool 

Inb4 Brett decides to get himself a swimming pool. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Inflatable swimming pool that it is. 

  • Haha 2
53 minutes ago, r32-25t said:

Just some progress pics after removing the clutches out of the drum 76D98F9C-521D-48A3-B98A-D5D73B618367.thumb.jpeg.9027374b1aac905e3d6ef9ada642abe1.jpeg10101969-D09C-4416-989A-F719FAAF9139.thumb.jpeg.6cfcf5239f05db8077ac71f0a4fb1f94.jpeg

12 thin clutches and two thick clutches or I'm all wrong with that part? 

  • 2 weeks later...

I decided to do a 9 plate set up in the drum for the transfer case and did the required measuring for the clearance. I only needed to go up one plate size and lucky for me Ben @BK had one in his collection and was nice enough to sell it to me.60D38398-8F3F-46BC-8FF6-E99AC9129ED5.thumb.jpeg.708d11e3a3cf79e6904a13dd59d380d7.jpegClutches in the drum ready to go E9E21918-7521-466D-B30C-270D11F20150.thumb.jpeg.a25f0fc78c6cc62d1006ded487e600e7.jpegThen fitted all the chain and sprockets back inDFF1ED7E-726D-4349-926D-28C6162E8103.thumb.jpeg.387dcae390cab7679e9f93b0dbbfc07c.jpegand the case all back together with new seals, orings and new oil filter, it’s all ready to be fitted to the gearbox (just need a gearbox now)

just like to say thanks again to Ben for all the advise and selling me the plate can’t wait to drive it 

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...