Jump to content
SAU Community

Air-conditioning Drain Pipe

kingtube69

By kingtube69,
in General Maintenance

 Share

Recommended Posts

kingtube69 Experienced

kingtube69

Posted
Posted

Hi All,

My AC drain pipe was sitting against the dump pipe on my R33 after I put in a Hypergear turbo (ATR45SAT). I had it taken to JEM to get tuned but on the way home it started smoking so I bit the bullet and cut the drain pipe so I could get home without it smoking up and catching fire.

I'm not sure what to do now because if I use the aircon its going to drain onto the dump pipe and steam, rust and more than likely crack.

Has anyone come across this before? If so what did you do to fix it or get around it?

Pictures below

AD709293-2F53-459D-B56A-A6FADF6617BD_zps

E28070AD-2D5F-4D05-B6F9-8CAFD865F3C4_zps

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/461606-air-conditioning-drain-pipe/
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
Posted

Thanks to the thick adapter Tao welds on it pushes the dump back too far which melts the drain. If it gets bad enough it will flood inside the car. The dump will be fine as long as it isn't wrapped.

kingtube69 Experienced

kingtube69

Posted
  • Author
Posted (edited)

Thanks to the thick adapter Tao welds on it pushes the dump back too far which melts the drain. If it gets bad enough it will flood inside the car. The dump will be fine as long as it isn't wrapped.

Yep I'm not sure why it's so thick, I was worried that the dump would actually fit when I was looking at it.

So you think its OK for the drain to drip onto it? Not wrapped dump anyway :)

Fark, is that what the burning smell was when I went single. Just checked and mine is burnt down. So does it need to be rectified or is it OK to leave?

Glad to know I'm not the only one - Waiting for responses but someone on SAU FB page said just get a heat sleeve and get that onto it which I'll probably do if Scotty says that letting it drip on there isn't OK

Edited by kingtube69
89CAL Grand Master

89CAL

Posted
Posted

Get a steel pipe that will fit neatly inside the hose and clamp it on. Get a p-clamp that fits around the pipe then and bolt it somewhere that will bring it out of the way

Thats a basic idea but you can bend the pipe etc to make it fit properly

kingtube69 Experienced

kingtube69

Posted
  • Author
Posted

Not only will you find disgusting water splashing in the passenger footwell, you'll find your car filled with mosquitoes!

It doesn't leak into the cabin, its cut on the engine side and can still drain out its just that I dont want it running onto the dump pipe

Get a steel pipe that will fit neatly inside the hose and clamp it on. Get a p-clamp that fits around the pipe then and bolt it somewhere that will bring it out of the way

Thats a basic idea but you can bend the pipe etc to make it fit properly

The issue is that the bend in the rubber hose actually sits on the dump if its in place :(

zebra Grand Master

zebra

Posted
Posted

Yet... Let it melt back a bit more.

Poorly designed 'drop in' turbo considering most of you are running the exact same JJ dump.

Those hypergears must sit so far back....ive got like 4" clearance with my bolt on td06

hypergear Grand Master

hypergear

Posted
Posted

Its got plenty of clearance using a OEM dump pipe. Or should JJR be making dump pipes following OEM dump pipe angle? But Having said that not all jjr dump pipes touches either.

That Xforce dump in my R33 years back was trouble free, and so is Tomei.

I will seek alternatives ways to get the IWG assembly shorter.

kingtube69 Experienced

kingtube69

Posted
  • Author
Posted

Hmm, it's not that the lower part of the pipe sits against it so it would be hard to tie it off to the side. It's that the bend off the pipe sits against the bend of the dump pipe. Bit of a pain in the ass but I'll work something out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...