Jump to content
SAU Community

Recommended Posts

On 08/11/2021 at 10:01 AM, r32-25t said:

 It German beer is much better then Korean beer 

This I have to agree too, also their sausages are better.

Went to their beer festival a few years ago in Berlin, that was great fun! RSA? yeah nah, here's a pint and a landyard so you don't drop your beer.

 

Fab Brief: must use existing hole, don't want a new hole through the washer bottle like all the other R33 GTS-ts out there. Also minimum pie cuts where possible (I reckon they're ugly).

Result: Pretty damn happy with this 😁

IMG_20211109_123121_967.thumb.jpg.d274f790d1405b213471b9babddf9cdb.jpg

IMG_20211109_123111_542.thumb.jpg.0617144201d6200163d0df9a039a356f.jpg

 

  • Like 4

New hot pipe too, because why not. Also the existing one didn't fit too well as it was made to suit a HDi intercooler which sat a bit more forward when compared to the Plazmaman Pro core.

We haven't discussed cost yet 😅

 

IMG_20211111_161900_859.jpg

IMG_20211111_161910_746.jpg

IMG_20211111_161848_942.jpg

  • Like 3
On 12/11/2021 at 3:35 AM, Piggaz said:

No clamps behind the front bar?

As in the Plazma clamps? Nah normal silicone joiners and hose clamps are fine for me. Only going to run about 2 to 2.2bar of boost.

The TB, had no choice because of the DBW adaptor.

On 11/13/2021 at 4:37 PM, Dose Pipe Sutututu said:

Just confirms how mentally retarded I am throwing more money at it 😐

I think this applies to all of us here 

timmy burch repeating GIF by South Park

  • Like 1
  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...