Jump to content
SAU Community

Recommended Posts

On 08/11/2021 at 10:01 AM, r32-25t said:

 It German beer is much better then Korean beer 

This I have to agree too, also their sausages are better.

Went to their beer festival a few years ago in Berlin, that was great fun! RSA? yeah nah, here's a pint and a landyard so you don't drop your beer.

 

Fab Brief: must use existing hole, don't want a new hole through the washer bottle like all the other R33 GTS-ts out there. Also minimum pie cuts where possible (I reckon they're ugly).

Result: Pretty damn happy with this 😁

IMG_20211109_123121_967.thumb.jpg.d274f790d1405b213471b9babddf9cdb.jpg

IMG_20211109_123111_542.thumb.jpg.0617144201d6200163d0df9a039a356f.jpg

 

  • Like 4

New hot pipe too, because why not. Also the existing one didn't fit too well as it was made to suit a HDi intercooler which sat a bit more forward when compared to the Plazmaman Pro core.

We haven't discussed cost yet 😅

 

IMG_20211111_161900_859.jpg

IMG_20211111_161910_746.jpg

IMG_20211111_161848_942.jpg

  • Like 3
On 12/11/2021 at 3:35 AM, Piggaz said:

No clamps behind the front bar?

As in the Plazma clamps? Nah normal silicone joiners and hose clamps are fine for me. Only going to run about 2 to 2.2bar of boost.

The TB, had no choice because of the DBW adaptor.

On 11/13/2021 at 4:37 PM, Dose Pipe Sutututu said:

Just confirms how mentally retarded I am throwing more money at it 😐

I think this applies to all of us here 

timmy burch repeating GIF by South Park

  • Like 1
  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...