Jump to content
SAU Community

Recommended Posts

10 hours ago, BK said:

It's alive !

it is ben but not that well lol. it seems to me like the timing keeps jumping around no matter what we do. it starts really nice every time then as i watch it running with the timing light it starts to jump around like crazy after 5 seconds and wants to die. almost like the trigger kit is jumping between 2 teeth and doesnt have  a set home between 2 teeth or something i dunno mates. we tried for about 5 hours of different timing settings and what not. there is a error code on the haltech for the trigger kit. been wrenching non stop for 3 days maybe just tired but any help of info on this always appreciated. im a total newb on tuning but im pretty sure we have the ignition set at like 230 out of the full 720 cycle if that makes sense. im tripping out the car seems like its going to run great then timing jumps around and it starts blowing black like a diesel and fowls the plugs instantly and dies. you can here it start popping and being wierd in the video that was actually the best it ran. we have been through 4 sets of plugs (tourched these sets probably 10 times to so more like 40 times and im not kidding all night of tourching plugs and trying stuff. i just wanna go fast this cars kicking my ass.

This may have something to do with it. I’ve found 1 connector I don’t know where it goes, and I also found a “ground” that may be a power wire. It’s located near stock battery location area. Cheers mates let me know your thoughts.

4F103F65-F395-434C-A8F3-FE8430A2ECC9.jpeg

5EB49A44-9499-448A-947C-7E2CB5497DB1.jpeg

well looks like we figured this haltech with the prp trigger kit issue out. the bracket for the cherry by the crank was rubbing on the crank pulley when it turned so hopefully once we put back together properly its well again. so just a heads up for you newbs putting prp trigger kits on your rb26. it is a possibily of rubbing on crank pulley if installed incorrectly. cheers mates hopefully video of 22psi soon.

  • Like 1
8 hours ago, Duncan said:

glad it is working...but I'm pretty sure I mentioned spacing out the cam sensor a few pages back 😛

yeah  i recon....i thought you were talking about those 3 little spacers on the back of the trigger kit up top where the old cas used to be. living and learning haha! again thanks for all your help good friend your a patient good guy that doesnt post useless comments and make a guy feel bad for not being as knowledgable as others. cheers buddy.

Dropped her off for a wheel alignment today and some fresh ball joints up front and away we go mates! Finally get to drive my dream 20 years later since I owned my first Gtr I’ve always wanted a gtr that was an animal that I built myself....ish with a lot of help lol. So heres my chance. It’s not perfect but it was definitely the best I could do for the cash I had. I have a great wife that has supported me through this build and all my crap so thanks again my good mate I love you and will always have your back cheers.

CC7DEB08-36F5-4C61-8A26-2D5D92418819.jpeg

BE257DCB-3758-4BC3-89A3-45B82F0144F0.jpeg

4C833EB7-95F0-4E23-AE00-9DA7C1857B67.jpeg

  • Like 1
On 26/03/2021 at 7:15 PM, BK said:

It's alive !

Now it’s alive mate. And of course as soon as we are ready to tune we get 100km winds plus this lol....had mint roads now a bunch of snow. But that don’t stop the Canadians, Went for spark plugs this morning and seen a balling r35 just sending the snow. Nice to see at 8am 

BAE10EE8-1C2F-4432-93C1-CA5E42AF18B5.jpeg

A0CC305E-FA04-414C-B687-6BBD703B7428.jpeg

Just  got her running on 12 psi, she is no longer a giant paper weight mates. Gunna put some serious boost at it today with e85 and hopefully this car can finally light the lamp against some hellcats. 

8E911FC8-56C4-47AB-B559-EF4454B1D720.jpeg

i may not be down under like the boys in australia but my bank account is defintiely wayyyyy down under lol....ordered another CAS from kudo today to solve the car not starting when its hot hopefully. could be tuning but my CAS sounds like it has rocks in it and has no resistance when i spin it so could use a replacement anyway. if you have run into this hot start no start issue let me know. it will eventually start but i have to crank it like crazy or wait for a couple minutes and let it cool down then it fires right up

Congrats on making RBs great again, none of this twin bullshit 😊

Did you space out the CAS when you ran the motor with no timing belt cover? If not you'll eat up CAS units all day.

I remember calling Nissan about a new CAS (before the GT-R boom), they wanted $2,000 (had to wait for it to come from Japan). Got a second hand one off fatz for $50 (wasn't an issue, was the AFM)s. But yeah, be careful with those, they cost a pretty penny these days :P

Ordered a new cas from kudo even tho going to try the prp trigger again. we have been tuning like crazy last few days. I am forsure going to have my timing cover back on and yes I have the spacers behind the cas. I have the stock cas seal behind there and the little spacers are inside it. We are going to go back to the prp trigger once the new hall sensor gets here....all was well at 16 psi today and then this happened.....I’m probably the first reporter of this but that’s my luck, the car always tries to kill me. Snapped by gktech bar clean off at 140km and well I’m sure you could imagine what that was like mates, fricken back and worth 10 times before I got the prick of a thing to settle down.

16DCE457-0A96-4D8B-B240-970DD7BAE33A.jpeg

88EED1B5-3D04-4A94-A882-6A14B4E39368.jpeg

1AB690D9-C56C-4010-9239-1A2ADE0B2ED6.jpeg

5E91E752-591A-4936-ABD2-040A8FD001E9.jpeg

good old gtr was dragging that bar the whole way home for 25km on the shoulder lol. champion. gotta contact gktech and find out why the hell this happened. if anyone has a lead on a better kit out there be my guest and let me know because im tripping out this gktech kit now...

2 hours ago, MoMnDadGTR said:

gotta contact gktech and find out why the hell this happened.

My suggestion is.....when you tightened it up you ended up with the spherical joint hard up against one side. You have to be real careful with these to make sure that the ball is centred when the arm is on, tight and sitting at ride height. If it is hard up against one side, or has very little travel left on one side, then when you move the joint in that direction it changes from a beraring to a pin joint instantly and you get all the torque on tha arm applied across the section of the thread.

  • Like 2
7 hours ago, Dose Pipe Sutututu said:

Damn!

Here I was going to buy everything GKTech (running a mix of yumcha arms & Hard Race ones, mainly rose joints and flogged from 5+ years of track work)

i really dont want to be the newb that says gktech stuff is no good cause shit does happen... i have all the rest of there stuff and i am the first reporter of this. i feel like i did something wrong like a) we took it for a real good drive before the wheel alignment was dont and the car was super toed in at the time(to the point where the tires were feathering from brand new), or b) i did drive it a bit and the nuts at the end of the bars were not tightened down completely, then we did the alignment and tightened em down good and the bars broke 100km later. i could easily not say all this stuff but want to be honest as i dont think it was the kits fault i think the wheel alignment should of been done right off the bat. but a broken bar cause of that seems nuts to me.  i feel like the old steering rack is stronger than this kit.....looks like a cheap metal ill send better pics. 

 

6 hours ago, BK said:

Holy shit dude....you and this car are not very good friends at all.

Midori Seibi would be my vote for a different / better quality Hicas delete kit.

benny boy ya good mate hows this for an idea...we are going to take the kit to a machine shop that makes drives shafts etc today and have them make the exact same kit but in a chromoly steel. or just try another gktech bar and do as gtsboy said...seemed like a pretty decent answer. kit could of been installed wrong from the start maybe i dunnno chap. Moral of the story is my gtr hates me and im scared of it every time i get it running right she blacks out and tries to stick me under the dirt...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...