Jump to content
SAU Community

Recommended Posts

Hi all,

Just wanting some advice regarding grout filling blocks.

Long story short, i am looking at building a new short block for my car as the current one has a 1mm crack that has been JB Welded and with the power it will eventually fail.

I have managed to find a virgin block r32 rb26 block, plan is to go billet main caps and plate. After talking to a few people online some people running big power on the cast blocks have also done grout fill along with bracing of some sort. I have talked to my engine builder about the idea of going half grout fill as it is still a street car and the setup for billet block is out of the question.

My engine builder has used Hardblok on old V8's, however they were for dedicated drag cars on methanol so heat is not really an issue. The issue is he has concerns about the grout separating from the bores from heat expansion with the different materials.

 

Cheers 

Jeff

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/
Share on other sites

  • 4 weeks later...

I think that the conservative approach is to grout up to the bottom of the lowest welch plug(s). Adds some stiffness but still allows the coolant pretty much full access to the bores. It doesn't put any grout around the part of the bore that might expand from internal pressure, but it certainly locates a clamp around the bore which constrains how far down the bore any such movement can occur, thereby reducing the amount of movement that can occur in the top half.

Perfect? No. Better than nothing? Of course.

There have been many people on here who have done pretty much what I described above. Read these.

https://www.sau.com.au/forums/topic/429446-strengthening-a-rb26-block/

https://www.sau.com.au/forums/topic/431462-grout-fill/

https://www.sau.com.au/forums/topic/210084-rb26-resin-filled-blocks/

 

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7952919
Share on other sites

My experience counts for zero as my engine has done no more than idle in the shed but I've done the grout fill to the base of the welsh plugs.  The lower part of the engine is the most common (only??) place that the blocks crack so makes sense to me to do it.  The hottest part of the block (top 4 inches where combustion happens) is not affected by grout so I see zero issues there.  I really see no downsides to it so if it only made 10% improvement surely it's worth it for the minimal expense of doing it.  I look at this way.  If I cracked a block and HADN'T done the grout, I'd never forgive myself for not giving it a fighting chance!

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7952920
Share on other sites

On 6/15/2021 at 4:01 AM, GTSBoy said:

I think I've seen RB26 (in particular) failures up high on the exhaust side near #4.

I'm sure the half-filled grout would help additionally strengthen to some degree. Especially with a PRP brace. Are blocks still cracking on that area with either or?

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7952995
Share on other sites

20 hours ago, r32-25t said:

26 blocks are common for cracking the deck, talking to Herman from prp said even full prepped all high power 26 blocks will crack eventually 

What kind of cars are breaking 26 blocks? I was watching Herman's youtube videos from 2 years ago and he said a number of high power GTRs are running the brace and not cracking blocks. He did mention grout filling too. I'm sure times have changed..

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953031
Share on other sites

Grout fill won't hurt. It's cheap anyway so do it.

If block cracks anyway what's the point of spending 2k+ on a brace?

If youre pushing 400+kW in a 'street car' it aint gonna be as reliable as social media say it's gonna be anyway. *flame suit on*

Thats the sport. Make bulk power and shit breaks.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953044
Share on other sites

2 minutes ago, WantGTR said:

If block cracks anyway what's the point of spending 2k+ on a brace?

There's almost certainly shades of grey here. For one thing, every engine and block is different. There's a bell curve of outright strength. On top of that, there's all the thousands of variables of how that block has been treated across its years of use, the power level that it has been run at, the particular mods/method by which the power is being made (ie power from more revs or power from more cylinder pressure). + how it is used. Street vs circuit vs drag, etc etc etc.

Then the next shade of grey is, for any given block, wherever it falls on that bell curve, surely adding the block brace still has benefits. Making the bottom end even less likely to walk around, for one. But I'd still expect it to raise the limit of that block before it will break. Trouble is, you can't go pulling out anecdotal evidence of "this block ran for 2 years at XXX HP without a brace and was fine" and "this other block broke at less HP with a block brace added", because the bell curve created by adding up all the uncertainties is likely to be far wider than the difference in power of those engines.

Unless you are in a position to gather a large number of statistics your (anyone's) statistics must be taken with a huge grain of salt. Confidence levels are only built up by having many examples with almost no difference between them to describe the average behaviour of that type of example (along with the other statistical parameters of interest, particularly the SD). There's no point comparing two examples if the stats are so poor that the SD is several times wider than the difference between the examples.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953047
Share on other sites

1 hour ago, GTSBoy said:

There's almost certainly shades of grey here. For one thing, every engine and block is different. There's a bell curve of outright strength. On top of that, there's all the thousands of variables of how that block has been treated across its years of use, the power level that it has been run at, the particular mods/method by which the power is being made (ie power from more revs or power from more cylinder pressure). + how it is used. Street vs circuit vs drag, etc etc etc.

Then the next shade of grey is, for any given block, wherever it falls on that bell curve, surely adding the block brace still has benefits. Making the bottom end even less likely to walk around, for one. But I'd still expect it to raise the limit of that block before it will break. Trouble is, you can't go pulling out anecdotal evidence of "this block ran for 2 years at XXX HP without a brace and was fine" and "this other block broke at less HP with a block brace added", because the bell curve created by adding up all the uncertainties is likely to be far wider than the difference in power of those engines.

Unless you are in a position to gather a large number of statistics your (anyone's) statistics must be taken with a huge grain of salt. Confidence levels are only built up by having many examples with almost no difference between them to describe the average behaviour of that type of example (along with the other statistical parameters of interest, particularly the SD). There's no point comparing two examples if the stats are so poor that the SD is several times wider than the difference between the examples.

i agree with what you are saying, lots of variables to take into account. i was just trying to make a point :P

 

People tend to jump on the bandwagon and want to include all the latest fancy new parts whether they are necessary or not. With today's technology, making 1000 or more isnt as out of reach as it used to be. Fact is there are more and more engines out there making lots of power even without braces. Toward the top end of the power spectrum, i firmly believe none of these engines are reliable no matter how well they are built or what parts are thrown into them and they are no where near as 'streetable' as the internet makes them out to be.

Either way you go, grout/no grout, brace/no brace, billet/cast, it is going to cost money and expect failures - not if but when.

 

Happy Modding.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953053
Share on other sites

9 hours ago, WantGTR said:

i agree with what you are saying, lots of variables to take into account. i was just trying to make a point :P

 

People tend to jump on the bandwagon and want to include all the latest fancy new parts whether they are necessary or not. With today's technology, making 1000 or more isnt as out of reach as it used to be. Fact is there are more and more engines out there making lots of power even without braces. Toward the top end of the power spectrum, i firmly believe none of these engines are reliable no matter how well they are built or what parts are thrown into them and they are no where near as 'streetable' as the internet makes them out to be.

Either way you go, grout/no grout, brace/no brace, billet/cast, it is going to cost money and expect failures - not if but when.

 

Happy Modding.

I think a brace is pretty clear that it is actually a very worthy mod. Yes, we can argue that every mechanical part can break with enough heat and stress but your points are blinding the degree to which this is highly probable vs. not.

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953066
Share on other sites

10 hours ago, cachorro said:

I think a brace is pretty clear that it is actually a very worthy mod. Yes, we can argue that every mechanical part can break with enough heat and stress but your points are blinding the degree to which this is highly probable vs. not.

The grout is a no brainer, the brace is a bit different as the cost and effort involved is a lot higher once you factor in machining, etc.  At the end of the day it's like an insurance policy.  You hate paying for it and hope you don't need it but bloody thankful you did have it when you needed it!

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953073
Share on other sites

I remember not that long ago this topic coming up on a GTR page on FB. Herman stated that a block brace is essential for any serious build. Then Anthony Maatouk chimed in and stated he has never used a block brace on a 26 block, however all his builds use an N1 block, claimed over 150 builds and not one block crack, tagged numerous customers to confirm, cars that have been running for years. 
Now he also stated he is not against the brace and uses them in all of his RB30 builds. Just his opinion is they are not required in an N1 block. Now this sparked a lot of back and fourth between Maatouk and Herman. Was all very interesting to hear both sides of the argument. Herman stating he has seen numerous N1 blocks crack and Maatouk stating it was likely other factors that caused that, (pointing towards bad tune). 
from a more personal point a mate of mine has a Maatouk’s built 2.7, running a 76/75 making 1000+ hp, been running for about 3 years now without issue. (Not braced). 

  • Like 3
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953074
Share on other sites

On 6/18/2021 at 8:04 PM, Old man 32 GTR said:

I remember not that long ago this topic coming up on a GTR page on FB. Herman stated that a block brace is essential for any serious build. Then Anthony Maatouk chimed in and stated he has never used a block brace on a 26 block, however all his builds use an N1 block, claimed over 150 builds and not one block crack, tagged numerous customers to confirm, cars that have been running for years. 
Now he also stated he is not against the brace and uses them in all of his RB30 builds. Just his opinion is they are not required in an N1 block. Now this sparked a lot of back and fourth between Maatouk and Herman. Was all very interesting to hear both sides of the argument. Herman stating he has seen numerous N1 blocks crack and Maatouk stating it was likely other factors that caused that, (pointing towards bad tune). 
from a more personal point a mate of mine has a Maatouk’s built 2.7, running a 76/75 making 1000+ hp, been running for about 3 years now without issue. (Not braced). 

Herman's videos are on youtube on the Motive Video channel and they are worth the watch. I wonder on what grounds Maatouk claims a brace is not necessary. It could be true but as mentioned, where on the bell curve does each individual block sit. Also there could be dozens of combinations of variables. Do you have a link to the facebook post? Curious to read up on it.

 

Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953227
Share on other sites

8 hours ago, cachorro said:

Herman's videos are on youtube on the Motive Video channel and they are worth the watch. I wonder on what grounds Maatouk claims a brace is not necessary. It could be true but as mentioned, where on the bell curve does each individual block sit. Also there could be dozens of combinations of variables. Do you have a link to the facebook post? Curious to read up on it.

 

On the grounds that they have extensive experience and a solid track record of building the fastest RBs in the country. No other workshop comes close to having as many tough RBs as this place in the Australia or possibly the world. They certainly have credibility to make comments about the platform.

 

note: i am not a customer of theirs at all but just calling a spade a spade.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/482428-rb26-grout-fill/#findComment-7953233
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...